null

80 Series Land Cruiser (93'-97')

  • Gasket 15785-66010, oil cooler or water pipe (GSK-1)

    Gasket 15785-66010, oil cooler or water pipe

    This OEM gasket is used for the heater return pipe which sits on the thermostat housing on the 1FZ and you need only one. This is the SAME gasket used in the oil cooler kit and you would need two. Part number: 15785-66010 MADE in JAPAN

    $3.75
    Add to Cart
  • OEM High Beam Headlight 90981-13046 (HBH-1)

    OEM High Beam Headlight 90981-13046

    OEM High Beam Headlight found in pretty much most US-originated Toyota and Lexus vehicles but if you have a North American 70/80/100/200 then this is the high beam light for you. If you are looking for the low beam then this is the one you need. Part...

    $25.10
    Add to Cart
  • OEM Low Beam Headlight 90981-13047 (LBH-1)

    OEM Low Beam Headlight 90981-13047

    OEM Low Beam Headlight found in pretty much most US-originated Toyota and Lexus vehicles but if you have a North American 70/80/100/200 then this is the low beam light for you. If you are looking for the high beam then this is what you want. Part...

    $25.10
    Add to Cart
  • 15% Overdrive Machined Alt Pulley (OMP-1)

    15% Overdrive Machined Alt Pulley, 1FZ

    NOTE: FITS ANY 1FZ LAND CRUISER ONLY Is this required for your 1FZ Land Cruiser? No. But if you spend a lot of time sitting at or close to idle on the freeway in traffic, or slowly crawling up a hill, or idling at a parking lot trying to charge the...

    $162.50
    Add to Cart
  • Speedometer Sensor O-Ring, 96711-24030 (SSO-1)

    Speedometer Sensor O-Ring, 96711-24030

    This is the commonly leaking o-ring found under the speedocable on all 80 Series and 100 Series Land Cruisers with the A440F,A442F,A343F, and A750 transmissions. Part no: 96711-24030 (Replaces 96710-02030) Made in JAPAN

    $4.00
    Add to Cart
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • OEM Oil Filter-Medium 90915-40002 (OIL-2)

    OEM Oil Filter-Medium 90915-40002

    Medium Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). This is a slightly larger version of the smaller OEM Oil Filter-Small. If you want the larger made in Japan canisters you could try getting 15601-44011 but good...

    $13.90
    Add to Cart
  • 80 Series Fuel Tank Vent Hose and Clamps (FTH-1)

    80 Series Fuel Tank Vent Hose and Clamps

    If you have an 80 Series Land Cruiser then you already know the familiar smell of fuel vapor when the charcoal canister fails. But did you know that there is another source of the fuel vapor smell on our aging trucks? Turns out there is a secondary fuel...

    $17.25
    Add to Cart
  • 80 Series Antenna Mast and Bezel Kit (AMB-1KIT)

    80 Series Antenna Mast and Bezel Kit, 96-97

    This is the kit for the 96-97 LX450 and the 97 40th Anniversary Land Cruisers. Earlier 80 Series antennas uses a mast that is no longer available from Toyota but can be found in the aftermarket world. If an OEM replacement is found I will update here...

    $104.80
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $38.45
    Add to Cart
  • 90915-YZZD3 OEM Oil Filter (OIL-1)

    OEM Oil Filter-Small

    Small Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). If you want the larger made in Japan canisters you could try getting 15601-44011. Part no. 90915-YZZD3 MADE in THAILAND

    $5.10
    Add to Cart
  • Battery Hold-Down Nuts

    Battery Hold-Down Nuts

    This is the OEM battery hold-down nut used on the battery tray hardware. Yes there is supposed to be TWO nuts PER clamping bolt. Part no: 90080-18071 sold separately MADE in JAPAN

    $1.50
    Add to Cart
  • 80 Series Battery Hold Down Hardware Set (BHD-1SET)

    80 Series Battery Hold Down Hardware Set

    This is the complete hardware set for all 80 series Land Cruisers RHD or LHD and passenger or driver side battery mounting.  If you have a battery set plate bar that is rusted to crap or have missing nuts for the clamp bolts, this will get you...

    $46.60
    Add to Cart
  • 80 Series Visor Clip Cap (VCC-1)

    80 Series Visor Clip Cap Pair

    This product ONLY makes sense if you have replaced your saggy/torn/limp visors with the upgraded Rosen aircraft visors. Once installed the stow clip becomes useless and is an eye sore. This cleans up the look. If you prefer a less expensive 3D printed...

    $35.00
    Add to Cart
  • Overflow Tank Cap Gasket- 60/62/80 Series (OCG-1)

    Overflow Tank Cap Gasket- 60/62/80 Series

    Every get really frustrated with your 25+ year old 60/62/80 Series Land Cruiser and the fact that the radiator overflow cap doesn't fit snugly onto the bottle because the gasket just plain wore out? Then you find out the only way to get a replacement...

    $6.90
    Add to Cart
  • 80 Series 1FZ Master Cylinder Assembly (MCA-1)

    80 Series 1FZ Master Cylinder Assembly

    NOTE: This master cylinder fits US spec 95-97 1FZ Land Cruiser and LX450 OEM replacement master cylinder for the FZJ80 Land Cruiser or LX450. This is a 4-bolt mount. Part no: 47201-60551 MADE in JAPAN

    $285.10
    Add to Cart
  • 80 Series OEM 1FZ Water Pump Assembly (WPA-1)

    80 Series OEM 1FZ Water Pump Assembly

    This is an official TOYOTA water pump for the 1FZ engine. This is not a "value" part or a gray market AISIN with all the logos scraped off. Yes you can absolutely save money by going the AISIN Amazon route but this is not for those people. Includes the...

    $200.00
    Add to Cart
  • 80 Series Rear Heater Delete Block-Off Plate (RHD-2)

    80 Series Rear Heater Delete Block-Off Plate

    If you have an 80 Series Land Cruiser there seems to inevitably be a decision made about whether or not to remove the rear heater. The typical reasons for removing it are:• Rear heater core is leaking inside the cab• The rear heater pipes are...

    $67.50
    Add to Cart
  • 80 series Transmission Hose Clamp (THC-1) 90467-A0012

    80 series Transmission Hose Clamp

    For the 80 Series Land Cruiser with automatic transmissions all use the same hose clamps for all of of the 3/8" transmission hoses. In case you get to the trans fitting nozzles and they need to be replaced you can find them here: 80 Series 1FZ Radiator...

    $3.40
    Add to Cart
  • 80 Series 1FZ OEM Knock Sensor (NOK-1)

    80 Series 1FZ OEM Knock Sensor

    All 80 Series 1FZ Land Cruisers utilize two knock sensors that simply detect pre-detonation (knock) and will send signal to adjust distributor advance to compensate. Fuel quality plays a direct part in how the knock sensor does its job. These OEM sensors...

    $175.40
    Add to Cart
  • 80 Series 1FZ Valve Cover Bolts (VCB-13)

    80 Series 1FZ Valve Cover Bolts

    This is a new set of valve cover bolts used on the 1FZ engine. Generally you can just reuse the old bolts but for those that are painting or hydro-dipping your valve cover and want new bolts, here you go. This is of course the ideal time to do the valve...

    $16.85
    Add to Cart
  • 80 Series Battery Box Grommet (BBG-1)

    80 Series Battery Box Grommet

    All 80 Series Land Cruiser battery boxes have two holes for the positive and negative battery cables to pass through. From the factory they came with rubber grommets to help prevent the cables from rubbing against the battery case. A LOT of cruisers are...

    $12.30
    Add to Cart
  • 80 Series 1FZ EGR Modulator (EGR-2)

    80 Series 1FZ EGR Modulator

    Generally speaking you'll know that the EGR modulator needs to be replaced because either the top cap is melted/missing and/or you get the PO401 and just replacing vacuum hose leaks didn't solve the issue. Replacing the modulator is a good time to...

    $135.20
    Add to Cart
  • 80 Series 1FZ Fuel Pressure Regulator Kit (FPR-1KIT)

    80 Series 1FZ Fuel Pressure Regulator Kit

    Ever notice in your 80 Series 1FZ Land Cruiser that you have a rough and/or issues starting when the engine is hot and/or the truck is running too rich and/or you have a PO301-306 check engine light? Or maybe a PO172? Chances are your Fuel Pressure...

    $152.00
    Add to Cart
  • 80 Series Wiring Harness Clamp (WHC-1) 82711-3H180

    80 Series Wiring Harness Clamp

    If you have an 80Series gas Land Cruiser then you have a wiring harness that travels from the behind the glovebox, out into the engine, and across the fire4wall to the end point connectors. On the first firewall attachment is a clamp that keeps it...

    $6.90
    Add to Cart
  • 80 Series 1FZ Oil Cooler Kit (OCK-1)

    80 Series 1FZ Oil Cooler Kit

    The 80 Series 1FZ oil cooler is often ignored unless its an engine rebuild. But the sad news is the oil cooler an be jammed up with gunk or even be a source of an oil or coolant leak. The location of the oil cooler isn't in a great location and requires...

    $54.00
    Add to Cart
  • 80 Series Inner Weatherstrips for the Door Glass (WDG-1KIT)

    80 Series Inner Weatherstrips for the Door Glass

    These are the INNER weatherstrips found on each of the doors. These are inside of the vehicle and not to be confused with: 80 Series Door Belt Molding Set. Includes:• (2) 68170-60030 WEATHERSTRIP ASSEMBLY, FRONT DOOR GLASS, INNER • (1)...

    $172.35
    Add to Cart
  • 80 Series 1FZ OEM PHH Tube (PHT-1)

    80 Series 1FZ OEM PHH Tube

    Well, its bound to happen. In the photos you will see a rusted PHH pipe. That rusty PHH pipe is from a SoCal truck with 380k miles on it. So-freaking-Cal and it was rusted out. Ugh. The pipe is directly connected to the block and straight up through one...

    $73.45
    Add to Cart
  • 80 Series Quarter Panel Belt Moulding Set (BMS-1)

    80 Series Quarter Panel Belt Moulding Set

    These are the two rear quarter belt mouldings on the 80 Series Land Cruiser that sit just under the rear sliding windows. These are separate from the door belt mouldings as they don't see the same wear as the windows because these don't see arms resting...

    $110.00
    Add to Cart
  • 80 Series 1FZ Evap Hose Set (EVS-1)

    80 Series 1FZ Evap Hose Set

    These are the evap hoses coming off the top of the charcoal canister on 95-97 80 Series 1FZ Land Cruisers. Typically these hoses are brittle and cracking and should be replaced. Good time to also change out your Toyota Truck Fuel Cap and inspect your...

    $49.05
    Add to Cart
  • OEM Switch Bulb (IPL-3) 84999-10420

    OEM Switch Bulb

    Although this bulb fits many Toyota models, this fits the 80 Series Land Cruiser in *some* of the switches. Best to look up your exact application to see if it fits. Part number: 84999-10420 MADE in JAPAN  

    $10.30
    Add to Cart
  • Switch Bulb, 14V 0.84W (IPL-2) 84999-10320

    Switch Bulb, 14V 0.84W

    Although this bulb fits many Toyota models, this fits the 80 Series Land Cruiser in *some* of the switches. Best to look up your exact application to see if it fits. Part number: 84999-10320 MADE in JAPAN  

    $10.10
    Add to Cart
  • JDM Shiftlock Button Reproduction- RED (SLB-1)

    JDM Shiftlock Button Reproduction- RED

    Did you know that early 80Series got a black shift lock button on the shifter console? Cool right? The later 80s were denied. Did you know that the JDM 80s not only came with the button but they are RED?! Yeah thats not fair. So we went ahead and...

    $63.00
    Add to Cart
  • 80 Series 1FZ OEM Timing Chain Tensioner (TCT-2)

    80 Series 1FZ OEM Timing Chain Tensioner

    Toyota switched out to a hydraulic unit that operates by oil pressure from a ratcheting version early in the 1FZ history. This tensioner is the OEM unit readily available and not to be confused with the modified ratcheting tensioner that is sometimes...

    $47.00
    Add to Cart
  • 1FZ Head Bolt and Washer Set (HBW-1)

    1FZ Head Bolt and Washer Set

    Doing a head gasket on your 1FZ powered 80 Series Land Cruiser? In doing so you'll need to remove the cylinder head which means removing the head bolts. This ia a complete replacement set of head bolts and washers. Includes:• (14)...

    $367.50
    Add to Cart
  • 1FZ Flexplate Mounting Bolt Set (FMB-1)

    1FZ Flexplate Mounting Bolt Set

    When having your engine rebuilt, or getting a new short block from Toyota, its a good idea to replace the flexplate bolts with new OEM bolts. That being said, Toyota engineers do not specify these are non-reusable so you are ok reusing your old bolts...

    $25.50
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Inner Axle Seal, Front- 70/80 Series (IAS-1)

    Inner Axle Seal, Front- 70/80 Series

    Inner axle seal for the 80 Series Land Cruisers. Also fits the 70 Series and 105 Series. If you have a groove on the journal of the inner axle shaft then you can overdrive seal using the 80 Series Inner Axle Seal Offset Driver. Part no:...

    $9.60
    Add to Cart
  • Toyota 4WD Solid Axle Front Wheel Bearing Set (FWB-1SET)- KOYO

    Toyota 4WD Solid Axle Front Wheel Bearing Set- KOYO

    These are the Made in Japan KOYO bearings for the front wheels on nearly every solid axle 4WD Toyota out there. For the 80 Series Land Cruiser these seem to be the flavor that most are gravitating to. Timken are the other brand possibility and although I...

    $122.00
    View Details
  • 80 Series Rear Airbag/Bump Stop Landing Pad Set (LPS-1)

    80 Series Rear Airbag/Bump Stop Landing Pad Set

    This is something that should ONLY be considered for your 80 Series Land Cruisder if you FIRST are installing Delta's 80 Series Rear Spring Retainer AND you are going to run either Firestone or Airlift rear bags  OR if you are going to install King...

    $130.00
    Add to Cart
  • 80 Series 1FZ "Gas" Filter (GAS-10)

    80 Series 1FZ "Gas" Filter

    Although this "gas filter" fits many Toyota models with many engines, its an item that is constantly broken on the 1FZ 80 Series landcruiser because its right up on top of the manifold and it doesn't take much to break off the little nipple. Part no...

    $38.50
    Add to Cart
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • 80 Series Center Diff Lock Switch, 93-97 only (CDL-1)

    80 Series Center Diff Lock Switch, 93-97 only

    US bound 80 Series Land Cruisers never came with the Center Diff Lock Switch even though the harness and plug is in the dash rear to plug one in. Adding this button gives you the ability to manually control the center diff. But doing the additional pin-7...

    $130.75
    Add to Cart
  • 80 Series Land Cruiser Spindle Sub-Assembly (SSA-1)

    80 Series Land Cruiser Spindle Sub-Assembly

    80 Series Land Cruiser Spindle Sub-Assembly that fits ALL 80 Series including FJ80, FZJ80, HDJ80 and HDJ81 Land Cruisers. The spindle is the same part number for either side. This spindle uses the needle bearing and bronze bushing as opposed to the solid...

    $347.00
    Add to Cart