null

80 Series Land Cruiser (91'-92')

  • Dual Fuel Tank Lever Knob (DTK-1)

    Dual Fuel Tank Lever Knob

    Replacement dual tank fuel knobs for 77324-60011 and 77324-60012 which are now obsolete. Commonly found on nearly all Land Cruisers with a fuel door tank selector knob. The original from Toyota is made from Bakelite and is either gone or cracked...

    $27.50
    Pre-Order Now
  • Toyota Speedo-Luber (LUB-1)

    Toyota Speedo-Luber

    NOTE: Only 10 in stock ready to ship. The rest will be on pre-order status.NOTE x2: This ONLY applies to those with an actual cable NOT a speed sensor #3FEMafia If you have a pre-93 Toyota Land Cruiser, or other Toyota 4WD truck with a speedometer...

    $51.00
    Pre-Order Now
  • Speedometer Sensor O-Ring, 96711-24030 (SSO-1)

    Speedometer Sensor O-Ring, 96711-24030

    This is the commonly leaking o-ring found under the speedocable on all 80 Series and 100 Series Land Cruisers with the A440F,A442F,A343F, and A750 transmissions. Part no: 96711-24030 (Replaces 96710-02030) Made in JAPAN

    $3.88
    Add to Cart
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • OEM Oil Filter-Medium 90915-40002 (OIL-2)

    OEM Oil Filter-Medium 90915-40002

    Medium Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). This is a slightly larger version of the smaller OEM Oil Filter-Small. If you want the larger made in Japan canisters you could try getting 15601-44011 but good...

    $13.80
    Add to Cart
  • 80 Series Fuel Tank Vent Hose and Clamps (FTH-1)

    80 Series Fuel Tank Vent Hose and Clamps

    If you have an 80 Series Land Cruiser then you already know the familiar smell of fuel vapor when the charcoal canister fails. But did you know that there is another source of the fuel vapor smell on our aging trucks? Turns out there is a secondary fuel...

    $17.25
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $35.40
    Add to Cart
  • Battery Hold-Down Nuts

    Battery Hold-Down Nuts

    This is the OEM battery hold-down nut used on the battery tray hardware. Yes there is supposed to be TWO nuts PER clamping bolt. Part no: 90080-18071 sold separately MADE in JAPAN

    $1.50
    Add to Cart
  • 80 Series Battery Hold Down Hardware Set (BHD-1SET)

    80 Series Battery Hold Down Hardware Set

    This is the complete hardware set for all 80 series Land Cruisers RHD or LHD and passenger or driver side battery mounting.  If you have a battery set plate bar that is rusted to crap or have missing nuts for the clamp bolts, this will get you...

    $46.60
    Add to Cart
  • 80 Series Visor Clip Cap (VCC-1)

    80 Series Visor Clip Cap Pair

    This product ONLY makes sense if you have replaced your saggy/torn/limp visors with the upgraded Rosen aircraft visors. Once installed the stow clip becomes useless and is an eye sore. This cleans up the look. If you prefer a less expensive 3D printed...

    $35.00
    View Details
  • Overflow Tank Cap Gasket- 60/62/80 Series (OCG-1)

    Overflow Tank Cap Gasket- 60/62/80 Series

    Every get really frustrated with your 25+ year old 60/62/80 Series Land Cruiser and the fact that the radiator overflow cap doesn't fit snugly onto the bottle because the gasket just plain wore out? Then you find out the only way to get a replacement...

    $6.90
    Add to Cart
  • 80 Series Rear Heater Delete Block-Off Plate (RHD-2)

    80 Series Rear Heater Delete Block-Off Plate

    If you have an 80 Series Land Cruiser there seems to inevitably be a decision made about whether or not to remove the rear heater. The typical reasons for removing it are:• Rear heater core is leaking inside the cab• The rear heater pipes are...

    $67.50
    Pre-Order Now
  • 80 series Transmission Hose Clamp (THC-1) 90467-A0012

    80 series Transmission Hose Clamp

    For the 80 Series Land Cruiser with automatic transmissions all use the same hose clamps for all of of the 3/8" transmission hoses. In case you get to the trans fitting nozzles and they need to be replaced you can find them here: 80 Series 1FZ Radiator...

    $3.10
    Add to Cart
  • 80 Series Battery Box Grommet (BBG-1)

    80 Series Battery Box Grommet

    All 80 Series Land Cruiser battery boxes have two holes for the positive and negative battery cables to pass through. From the factory they came with rubber grommets to help prevent the cables from rubbing against the battery case. A LOT of cruisers are...

    $10.80
    Add to Cart
  • 80 Series Wiring Harness Clamp (WHC-1) 82711-3H180

    80 Series Wiring Harness Clamp

    If you have an 80Series gas Land Cruiser then you have a wiring harness that travels from the behind the glovebox, out into the engine, and across the fire4wall to the end point connectors. On the first firewall attachment is a clamp that keeps it...

    $6.00
    Add to Cart
  • 80 Series Inner Weatherstrips for the Door Glass (WDG-1KIT)

    80 Series Inner Weatherstrips for the Door Glass

    These are the INNER weatherstrips found on each of the doors. These are inside of the vehicle and not to be confused with: 80 Series Door Belt Molding Set. Includes:• (2) 68170-60030 WEATHERSTRIP ASSEMBLY, FRONT DOOR GLASS, INNER • (1)...

    $150.75
    Add to Cart
  • 80 Series Quarter Panel Belt Moulding Set (BMS-1)

    80 Series Quarter Panel Belt Moulding Set

    These are the two rear quarter belt mouldings on the 80 Series Land Cruiser that sit just under the rear sliding windows. These are separate from the door belt mouldings as they don't see the same wear as the windows because these don't see arms resting...

    $96.30
    Add to Cart
  • OEM Switch Bulb (IPL-3) 84999-10420

    OEM Switch Bulb

    Although this bulb fits many Toyota models, this fits the 80 Series Land Cruiser in *some* of the switches. Best to look up your exact application to see if it fits. Part number: 84999-10420 MADE in JAPAN  

    $9.00
    Add to Cart
  • Switch Bulb, 14V 0.84W (IPL-2) 84999-10320

    Switch Bulb, 14V 0.84W

    Although this bulb fits many Toyota models, this fits the 80 Series Land Cruiser in *some* of the switches. Best to look up your exact application to see if it fits. Part number: 84999-10320 MADE in JAPAN  

    $10.10
    Add to Cart
  • JDM Shiftlock Button Reproduction- RED (SLB-1)

    JDM Shiftlock Button Reproduction- RED

    Did you know that early 80Series got a black shift lock button on the shifter console? Cool right? The later 80s were denied. Did you know that the JDM 80s not only came with the button but they are RED?! Yeah thats not fair. So we went ahead and...

    $63.00
    Pre-Order Now
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Inner Axle Seal, Front- 70/80 Series (IAS-1)

    Inner Axle Seal, Front- 70/80 Series

    Inner axle seal for the 80 Series Land Cruisers. Also fits the 70 Series and 105 Series. If you have a groove on the journal of the inner axle shaft then you can overdrive seal using the 80 Series Inner Axle Seal Offset Driver. Part no:...

    $9.60
    Add to Cart
  • Toyota 4WD Solid Axle Front Wheel Bearing Set (FWB-1SET)- KOYO

    Toyota 4WD Solid Axle Front Wheel Bearing Set- KOYO

    These are the Made in Japan KOYO bearings for the front wheels on nearly every solid axle 4WD Toyota out there. For the 80 Series Land Cruiser these seem to be the flavor that most are gravitating to. Timken are the other brand possibility and although I...

    $122.00
    View Details
  • 80 Series Rear Airbag/Bump Stop Landing Pad Set (LPS-1)

    80 Series Rear Airbag/Bump Stop Landing Pad Set

    This is something that should ONLY be considered for your 80 Series Land Cruisder if you FIRST are installing Delta's 80 Series Rear Spring Retainer AND you are going to run either Firestone or Airlift rear bags  OR if you are going to install King...

    $130.00
    Pre-Order Now
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • 80 Series Land Cruiser Spindle Sub-Assembly (SSA-1)

    80 Series Land Cruiser Spindle Sub-Assembly

    80 Series Land Cruiser Spindle Sub-Assembly that fits ALL 80 Series including FJ80, FZJ80, HDJ80 and HDJ81 Land Cruisers. The spindle is the same part number for either side. This spindle uses the needle bearing and bronze bushing as opposed to the solid...

    $347.00
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • 80/100 Series Transfer Indicator Switch (TIS-1)

    80/100 Series Transfer Indicator Switch

    On the 80 Series Land Cruiser this is used For the Transfer Indicator Switch No. 1 and No. 3. This should be the first check when you can't get the lockers to light up on the dash. These commonly go bad but they can be sprayed with brake clean and...

    $97.85
    Add to Cart
  • 80/100 Series Spindle Needle Bearing and Bushing Set (SNB-1)

    80/100 Series Spindle Needle Bearing and Bushing Set

    Opinions on these seem to vary pretty wildly. The 80 Series spindle originally came with a solid brass bushing but if you were to order a new Toyota OEM spindle it would come with this set of bushing and needle bearing. On the 100 Series Land Cruisers...

    $72.40
    Add to Cart
  • Rear U-Joint 4WD Toyota Trucks, 70/80/100/200 (FUJ-2)

    Rear U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM rear u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD HD trucks. This is for one u-joint but its the same joint for front and rear of the REAR driveshaft only. The front shaft takes a different u-joint. While replacing the...

    $70.80
    Add to Cart
  • 80 Series Front U-Joint, fits most 4WD Toyota Trucks (FUJ-1)

    Front U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM front u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD  trucks. This is for one u-joint but its the same joint for front and rear of the FRONT driveshaft only. The rear shaft takes a different u-joint. While replacing...

    $71.65
    Add to Cart
  • 80 Series Front Hood Strut Set (FHS-1)

    80 Series Front Hood Strut Set

    These are actual OEM Toyota 91-97 80/81 Series Land Cruiser front hood struts, not aftermarket.  Includes:• (1) 53440-69015 SUPPORT ASSY, HOOD, RH• (1) 53450-69015 SUPPORT ASSY, HOOD, LH MADE in JAPAN  

    $188.35
    Add to Cart
  • 80 Series OEM Tie-Rod Complete Kit (TRK-1)

    80 Series OEM Tie-Rod Complete Kit

    This is the complete OEM Tie-Rod end kit for all LEFT hand drive (LHD) 80 Series Land Cruisers. That being said the only difference for the RIGHT hand drive (RHD) 80 Series would be: 45044-69115 END SUB-ASSY, STEERING RELAY ROD, RH which is NOT...

    $277.25
    Add to Cart
  • 80 Series Door Belt Molding Set (DBM-1KIT)

    80 Series Door Belt Molding Set

    These are the OEM replacement trim pieces found on the top of each door of your 80 Series. When you roll the window down and place your arm our onto the top of the door and let your face feel the breeze, well those are the scratchy, faded and brittle...

    $313.00
    Add to Cart
  • 80 Series Cowl Heater Air Cover Kit (HAC-1KIT)

    80 Series Cowl Heater Air Cover Kit

    Underneath the windshield cowl for all 80 Series Land Cruisers live the Air Heater Covers. These act as screens to capture pine needles and leaves before they can enter the fresh air ducts in the truck. Or at least that's what they usually do. These tend...

    $47.90
    Add to Cart
  • 80 Series Rear Hatch Strut Set (RHS-1)

    80 Series Rear Hatch Strut Set

    These are actual OEM Toyota 91-97 80/81 Series Land Cruiser rear hatch struts, not aftermarket.  Includes:• (1) 68950-60040 Back Door Stay Assembly, Right• (1) 68960-60030 Back Door Stay Assembly, Left MADE in JAPAN

    $82.00
    Add to Cart
  • 80 Series 3FE Motor Mount Set (MMS-1)

    80 Series 3FE Motor Mount Set

    OEM motor mount set for the 80 Series with with the 3FE motor. The 3FE uses a L/R mount whereas the 1FZ uses ambidextrous mounts. Includes:• (1) 12361-61050 Front mount, left• (1) 12362-61010 Front mount, right MADE in JAPAN  

    $229.90
    Add to Cart
  •  The most hated hose clamp for 5/8" hose (POO-1) 87124-28030

    The most hated hose clamp for 5/8" hose

    Quite possibly THE most hated hose clamp in the Land Cruiser world. Personally the use of these clamps makes me ill but they have their place. Since I get requests for them every now and again it seemed time to just start stocking for those that REALLY...

    $3.70
    Add to Cart
  • 80 Series Heater Hose Clamp- 3FE/1FZ (HHC-1)

    80 Series Heater Hose Clamp- 3FE/1FZ, 1/2" ID Hose

    OEM heater hose clamp found on 80 Series Land Cruisers with 3FE and 1FZ engines. This clamp ONLY works on the 1/2" hoses and will not fit the 5/8" hoses. Specifically this clamp is used on the heater hoses used on the REAR heater.  Part no:...

    $2.75
    Add to Cart
  • 60/80 Series Headlight Washer Hose Valve (HWV-1)

    60/80 Series Headlight Washer Hose Valve

    On your 60/62/early 80 series, that were equipped with headlight washers, you my have noticed that either one side or both sides doesn't squirt properly. It very likely NOT a pump issue but is instead a bad Headlight Washer Hose Check Valve. These...

    $52.75
    Add to Cart
  • OEM Automatic Transmission Drain Plug and Washer (ADP-1)

    OEM Automatic Transmission Drain Plug and Washer

    OEM replacement drain plug and washer for nearly all Automatic Transmission Toyota cars and trucks. Oddly enough this doesn't fit PRE-95 Land Cruisers. The main reason for changing this plug out with every drain and refill is to prevent galling the...

    $5.90
    Add to Cart
  • DashHole Plug- Mount, with Notch (DPM-2) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, with Notch

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Pre-Order Now