null

62 Series Land Cruiser

  • Dual Fuel Tank Lever Knob (DTK-1)

    Dual Fuel Tank Lever Knob

    Replacement dual tank fuel knobs for 77324-60011 and 77324-60012 which are now obsolete. Commonly found on nearly all Land Cruisers with a fuel door tank selector knob. The original from Toyota is made from Bakelite and is either gone or cracked...

    $27.50
    Pre-Order Now
  • Toyota Speedo-Luber (LUB-1)

    Toyota Speedo-Luber

    NOTE: Only 10 in stock ready to ship. The rest will be on pre-order status.NOTE x2: This ONLY applies to those with an actual cable NOT a speed sensor #3FEMafia If you have a pre-93 Toyota Land Cruiser, or other Toyota 4WD truck with a speedometer...

    $51.00
    Pre-Order Now
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • OEM Oil Filter-Medium 90915-40002 (OIL-2)

    OEM Oil Filter-Medium 90915-40002

    Medium Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). This is a slightly larger version of the smaller OEM Oil Filter-Small. If you want the larger made in Japan canisters you could try getting 15601-44011 but good...

    $13.80
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $35.40
    Add to Cart
  • Overflow Tank Cap Gasket- 60/62/80 Series (OCG-1)

    Overflow Tank Cap Gasket- 60/62/80 Series

    Every get really frustrated with your 25+ year old 60/62/80 Series Land Cruiser and the fact that the radiator overflow cap doesn't fit snugly onto the bottle because the gasket just plain wore out? Then you find out the only way to get a replacement...

    $6.90
    Add to Cart
  • 4WD Hub Dial Hardware Set (HDH-1) 91641-80616

    4WD Hub Dial Hardware Set

    OEM 4WD hub dial hardware set for the 60 Series Land Cruiser. This set takes care of both sides. Includes:• (12) 91641-80616 Bolts MADE in JAPAN  

    $15.55
    Add to Cart
  • Front Wheel Stud- 40/60/70 Series (STD-3) 90942-02053

    Front Wheel Stud- 40/60/70 Series

    OEM front wheel stud for most early 4WD Toyota trucks. Part no: 90942-02053 Fits:• 1983-85 Toyota 4Runner• 1988-99 Toyota 4Runner• 1980-85 Toyota 40 Series Land Cruiser• 1984-99 Toyota 70 Series Land Cruiser• 1980-97 Toyota 60...

    $9.36
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Toyota 4WD Solid Axle Front Wheel Bearing Set (FWB-1SET)- KOYO

    Toyota 4WD Solid Axle Front Wheel Bearing Set- KOYO

    These are the Made in Japan KOYO bearings for the front wheels on nearly every solid axle 4WD Toyota out there. For the 80 Series Land Cruiser these seem to be the flavor that most are gravitating to. Timken are the other brand possibility and although I...

    $122.00
    View Details
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • Rear U-Joint 4WD Toyota Trucks, 70/80/100/200 (FUJ-2)

    Rear U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM rear u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD HD trucks. This is for one u-joint but its the same joint for front and rear of the REAR driveshaft only. The front shaft takes a different u-joint. While replacing the...

    $70.80
    Add to Cart
  • 60/62 Series A/C Idler Pulley (TIP-2)

    60/62 Series A/C Idler Pulley

    For the 60 and 62 Series Land Cruiser with the 2F/3FE engine this is the replacement A/C compressor idler pulley. There is a replacement bearing you can find online but its just a lot easier to simply replace the entire pulley.  TIP: for the P/S...

    $36.50
    Add to Cart
  •  The most hated hose clamp for 5/8" hose (POO-1) 87124-28030

    The most hated hose clamp for 5/8" hose

    Quite possibly THE most hated hose clamp in the Land Cruiser world. Personally the use of these clamps makes me ill but they have their place. Since I get requests for them every now and again it seemed time to just start stocking for those that REALLY...

    $3.70
    Add to Cart
  • Door/Hood Plug (DHP-1)

    Door/Hood Plug

    This plug is used on a HUGE swath of Toyota vehicles as a hood and body drain port plug. On the 60s these are used in the pillars but are often time missing. If you notice water being trapped in the body or water on the floor of your 60 then its very...

    $2.00
    Add to Cart
  • 60/62 Series Complete 3-Wiper Arm Assembly Kit (WAA-2K)

    60/62 Series Complete 3-Wiper Arm Assembly Kit

    NOTE: This is for those wanting to stay original setup. This is NOT the 4Runner arm mod. This is the complete wiper arm assembly kit for the 60 and 62 Series Land Cruiser. These are the complete arms, wipers and hardware needed to completely freshen up...

    $298.00
    Add to Cart
  • 60/62 Series Windshield 3-Blade Wiper Kit (WBK-2)

    60/62 Series Windshield 3-Blade Wiper Kit

    OEM windshield wiper blade replacements for the 60 Series and 62 Series Land Cruiser. This set includes both front and the rear blades. If you are looking for the entire blade and arm kit >> Includes:• (1) 85220-16270 Replaced by:...

    $54.00
    Add to Cart
  • 60/80 Series Headlight Washer Hose Valve (HWV-1)

    60/80 Series Headlight Washer Hose Valve

    On your 60/62/early 80 series, that were equipped with headlight washers, you my have noticed that either one side or both sides doesn't squirt properly. It very likely NOT a pump issue but is instead a bad Headlight Washer Hose Check Valve. These...

    $52.75
    Add to Cart
  • OEM Automatic Transmission Drain Plug and Washer (ADP-1)

    OEM Automatic Transmission Drain Plug and Washer

    OEM replacement drain plug and washer for nearly all Automatic Transmission Toyota cars and trucks. Oddly enough this doesn't fit PRE-95 Land Cruisers. The main reason for changing this plug out with every drain and refill is to prevent galling the...

    $5.90
    Add to Cart
  • DashHole Plug- Mount, with Notch (DPM-2) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, with Notch

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Pre-Order Now
  • DashHole Plug- Mount, Notch-Free Face (DPM-1) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, Notch-Free

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Add to Cart
  • Horn Contact Pin "Plate" (PIN-1)

    Horn Contact Pin "Plate"

    This OEM horn pin fits just about every Toyota on the road from 1974 til about 1990ish. The applications are too many to list. But if your horn uses this style of pin this is likely the one. The issue with the horn not working is very typically that this...

    $7.60
    Add to Cart
  • 62 Series 3FE Radiator Hose & Clamp Kit (RHK-5)

    62 Series 3FE Radiator Hose & Clamp Kit

    This is the Radiator and Hose kit for the 62 SERIES 3FE motor. This kit does NOT fit the 80 Series 3FE. Includes:• (1) 16572-61020 • (1) 16573-61060• (1) 16571-61040• (2) 90466-41008• (4) 96111-10510 MADE in JAPAN

    $108.40
    Add to Cart
  • 60 Series Dome Light Lens (DLL-2)

    60 Series Dome Light Lens

    Dome light lens found on 80s and 90s Toyota Trucks and cars. Original is very likely either crumbling or very yellow or melted. Part no: 81241-20060 Fits:• Toyota 4Runner 1984-1995 • Toyota Land Cruiser 1981-1990 • Toyota Pickup 1984-1995...

    $8.35
    Add to Cart
  • 62 Series Fuel Door Release Handle (FDR-1)

    62 Series Fuel Door Release Handle

    Have a 62 Series Land Cruiser? How's your fuel door pull knob? Is it cracked? Are you using vice grips to pull the wire to open the fuel door? This is a CNC machined replacement for that fuel door pull knob. This is machined from aluminum, anodized...

    $44.00
    Add to Cart
  • 10-pack Steel Diff Plug washers (SDP-1)

    10-pack Steel Diff Plug washers

    OEM Toyota Drain Plug Gasket- steel for differentials. These are one-time use replacement washers used in OEM Magnetic Differential Plug Kit. Part no: 12157-10010 10-PK Made in JAPAN

    $15.00
    Add to Cart
  • 10-pack Aluminum Transfer Plug washers (ATP-2)

    10-pack Aluminum Transfer Plug washers

    OEM Toyota Drain Plug Gasket- aluminum for transfer cases and transmissions. These are one-time use replacement washers used in OEM Magnetic Transfer or Trans Case Drain Plug Kit Part no: 90430-A0003 10-PK Made in USA

    $17.40
    Add to Cart
  • 3FE Tune-Up Master Kit (TMK-3)

    3FE Tune-Up Master Kit

    Toyota Land Cruiser 80 Series (and MOSTLY 62 Series as noted) 3F-E Tune Up Parts and Tidbits based on the list put together, and with permission, by Jon Held on IH8MUD (6) 90919-01091 Spark PlugsCorrect electrode gap: 1.1 mm (0.043 in.) (1)...

    $314.10
    Add to Cart
  • Body Grease- Molykote 102 (BGM-102)

    Body Grease- Molykote 102

    This is the Toyota specific grease used in electrical motors on the Land Cruisers. Typical applications would be the windshield motors and the diff e-lock motors that commonly need to be rebuilt. One bottle is easily enough for two motor's worth of...

    $58.75
    Add to Cart
  • 3FE Head Bolt- Front (HBF-3)

    3FE Head Bolt- Front, CNC Machined

    For those that say I don’t give any attention to the anemic 3FE boat anchor, well here you go, it’s getting love.  On the 3FE motor, the front two head bolts are also used to mount the air pump. Those two bolts are NLA. Used are either...

    $95.00
    View Details
  • OEM 25mm Spring and Bolt Clamp for 3/4" hoses (SBC-25)

    OEM 25mm Spring and Bolt Clamp for 5/8" ID hoses

    On the 80 Series 3FE and 1FZ engines, all of the heater hoses are secured by a spring steel clamp that is tightened at the factory using a cotter pin and tool to lock it into place. These are intended as single use clamps. If you still have these clamps...

    $0.50
    Add to Cart
  • Land Cruiser Starter Mounting Stud- M12 (SMS-12)

    Land Cruiser Starter Mounting Stud- M12

    This is the starter mounting stud used on all 1FZFE, 2F, 3FE, F motors up to 1993. Part no. 90116-12005 This stud measures:• 43mm length• M12 x 1.25 x 18mm fine thread• M12 x 1.75 x 8mm course thread Made in USA

    $1.90
    Add to Cart
  • Land Cruiser Shock Bolt and Washer (SBW-1)

    Land Cruiser Shock Bolt and Washer

    These are the shock bolts that are used in several models of Land Cruiser. These tend to not only rust out but they also tend to get damaged during off-roading. Part no: 90119-12088• 60/62 series: rear upper and lower, front lowers (6 needed)•...

    $3.20
    Add to Cart
  • 11mm Driveshaft Bolt- Spare (DCS-11)

    11mm Driveshaft Bolt- Spare

    Individual OEM 11mm driveshaft bolt. Although you can get an entire 10mm driveshaft hardware or 11mm driveshaft hardware kit, sometimes it helps to have a few 11mm bolts as a spare.

    $1.50
    Add to Cart
  • Toyota FIPG 1281 Adhesive (TOY-1281)

    Toyota FIPG 1281 Adhesive

    TOYOTA OEM specified RED adhesive for the transmission pan. Formed-in-Place Transmission Gasket is a high-performance RTV silicone used as a formed-in-place transmission gasket to seal various flange and large clearance surfaces in order to prevent oil,...

    $26.70
    Add to Cart
  • Glovebox Insert for RHD 60/62 Series Land Cruiser (GBI-2)

    Glovebox Insert for RHD 60/62 Series Land Cruiser

    You know that lame cardboard insert in your glovebox that field mice just LOVE to use as nesting material? Well now you have an aluminum alternative that is a bolt-on replacement. Simply unbolt the door, unscrew the old insert and screw in the new insert...

    $235.00
    Add to Cart