null

60 Series Land Cruiser

  • Toyota Magnetic Differential Plug Kit (DPK-1)

    OEM Magnetic Differential Plug Kit

    These OEM Magnetic Differential Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs with M18 threads. These are the hex plugs that replace the easily damaged diff fill and drain plugs. The originals can be easily damaged from off-roading or from a...

    $11.45
    Add to Cart
  • Gates Green Stripe heater hose 5/8" by the foot (GAT-58)

    Gates Green Stripe heater hose 5/8" by the foot

    Although its not OEM its the next best thing to replace the direct runs of heater hose in your truck. Note: the quantity selected will be in a single length of hose Features:• Green Stripe® construction provides best cost-per-mile...

    $3.25
    Add to Cart
  • OEM Magnetic Transfer or Trans Case Drain Plug Kit (DPK-2)

    OEM Magnetic Transfer or Trans Case Drain Plug Kit

    These OEM Magnetic Transfer Case Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs (does not fit the FJ Cruiser auto). These are the hex plugs that replace the easily damaged drain plugs. The originals can be easily damaged from a tool rounding out...

    $11.90
    Add to Cart
  • Oil Drain Bolt Gasket (ODG-10)

    Oil Drain Bolt Gasket

    There are your standard Toyota drain plug gaskets that should be replaced with every oil change. Part no: 90430-12031 Fits: Toyota FJ Cruiser 2007-2014 Toyota Land Cruiser 1991 - 2020 Toyota Pickup 1990 - 1995 Toyota Sequoia 2001-2020 Toyota T100...

    $10.45
    Add to Cart
  • Gates Green Stripe heater hose 1/2" by the foot (GAT-12)

    Gates Green Stripe heater hose 1/2" by the foot

    Although its not OEM its the next best thing to replace the direct runs of heater hose in your truck. Note: the quantity selected will be in a single length of hose Features:• Green Stripe® construction provides best cost-per-mile...

    $3.00
    Add to Cart
  • Land Cruiser Shock Bolt and Washer (SBW-1)

    Land Cruiser Shock Bolt and Washer

    These are the shock bolts that are used in several models of Land Cruiser. These tend to not only rust out but they also tend to get damaged during off-roading. Part no: 90119-12088• 60/62 series: rear upper and lower, front lowers (6 needed)•...

    $3.70
    Add to Cart
  • 80 Series Wheel Stud- Rear (STD-2)

    60/80 Series Wheel Stud- Rear

    OEM rear wheel stud for all 60 and 80 Series Land Cruisers. Part no: 90942-02052 Also fits:• 1981-1997 Toyota Land Cruiser• 1984-2000 Toyota 4Runner• 1979-1995 Toyota Pickup• 2001-2007 Toyota Sequoia• 1993-1998 Toyota...

    $6.75
    Add to Cart
  • OEM 25mm Spring and Bolt Clamp for 3/4" hoses (SBC-25)

    OEM 25mm Spring and Bolt Clamp for 5/8" ID hoses

    On the 80 Series 3FE and 1FZ engines, all of the heater hoses are secured by a spring steel clamp that is tightened at the factory using a cotter pin and tool to lock it into place. These are intended as single use clamps. If you still have these clamps...

    $0.50
    Add to Cart
  • Toyota FIPG 103 Adhesive (TOY-103) 00295-00103

    Toyota FIPG 103 Adhesive

    TOYOTA OEM specified adhesive for the oil pan and camshaft housing. Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings. OEM part # 00295-00103 • Assemble parts within 15...

    $18.00
    View Details
  • 10-pack Steel Diff Plug washers (SDP-1)

    10-pack Steel Diff Plug washers

    OEM Toyota Drain Plug Gasket- steel for differentials. These are one-time use replacement washers used in OEM Magnetic Differential Plug Kit. Part no: 12157-10010 10-PK Made in JAPAN

    $15.00
    Add to Cart
  • 80 Series Driveshaft Hardware Kit-Rear 11mm (DCS-3)

    80 Series Driveshaft Hardware Kit-Rear 11mm

    This is the complete driveshaft hardware for most Land Cruisers on the road. This kit replaces the washer/nut on the transfer case side and the bolt/washer/nut on the differential side. The 11mm rear driveshaft hardware fits:• All FJ60 Series Land...

    $32.70
    Add to Cart
  • Toyota Early Grill Clips (CLP-2)

    Toyota Early Grill Clip

    If you have a 60 Series Land Cruiser or 1st Gen Toyota 4Runner or Pickup, then you likely still have a grill holding on for deal life. So much so you are afraid of touching it and breaking the last good clip and substituting it for yet another ziptie...

    $2.30
    Add to Cart
  • Connector Pin Tool-basic (PST-2)

    Connector Pin Tool-basic

    If you own any Toyota long enough you will eventually need to either modify or repair an electrical connector. This can be daunting because it seems everyone is already having a hard enough time building up the courage to even commit to "cutting the...

    $43.00
    View Details
  • 10-pack Aluminum Transfer Plug washers (ATP-2)

    10-pack Aluminum Transfer Plug washers

    OEM Toyota Drain Plug Gasket- aluminum for transfer cases and transmissions. These are one-time use replacement washers used in OEM Magnetic Transfer or Trans Case Drain Plug Kit Part no: 90430-A0003 10-PK Made in USA

    $18.35
    Add to Cart
  • OEM Steel Wheel Chock (SWC-1)

    OEM Steel Wheel Chock

    It should go without saying that ALL vehicles should have a pair of wheel chocks for safety. Every time you are repairing your truck or replacing a tire or anything that requires you to be under it, a wheel chock is a must. If you have a pair of wheel...

    $26.70
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Wits' End patch (WEP-1)

    Wits' End patch

    The Wits' End more-al patch. Add one to your collection or start a collection today. More-al patches are fun as you display your interest to your peers and draw on that common bond of TEQ in the Land Cruiser community. Oh and no cheap Chinese junk,...

    $9.00
    Add to Cart
  • Check Yer Nuts More-Al patch (WEP-4)

    Check Yer Nuts More-Al patch

    If you have an 80 Series then you SHOULD know about the utter importance of checking your nuts! Specifically your knuckle stud hardware. Here's a patch to help remind you. Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT...

    $12.00
    View Details
  • 60 Series Door Regulator Handle Escutcheon (ESC-1)

    60 Series Door Regulator Handle Escutcheon

    Yes...escutcheon. I had to look up the word too, don't feel bad. These go behind the door handle on manual window crank handles. Part no: 69266-22010-08 es·cutch·eon /əˈskəCHən/ noun: escutcheon; plural noun: escutcheons; noun:...

    $1.75
    Add to Cart
  • 11mm Driveshaft Bolt- Spare (DCS-11)

    11mm Driveshaft Bolt- Spare

    Individual OEM 11mm driveshaft bolt. Although you can get an entire 10mm driveshaft hardware or 11mm driveshaft hardware kit, sometimes it helps to have a few 11mm bolts as a spare.

    $1.50
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • Wheel Stud Tool- 12mm Studs (WST-1)

    Wheel Stud Tool- 12mm Studs

    This tool all started because of this thread: RTH: stuck in Primm, wheel lugs sheered off All 6 wheel studs snapped while driving on the frwy coming home from Las Vegas at 60MPH. I was stuck with no way to replace the broken studs so I had to be towed...

    $55.00
    Add to Cart
  • Toyota FIPG 1281 Adhesive (TOY-1281)

    Toyota FIPG 1281 Adhesive

    TOYOTA OEM specified RED adhesive for the transmission pan. Formed-in-Place Transmission Gasket is a high-performance RTV silicone used as a formed-in-place transmission gasket to seal various flange and large clearance surfaces in order to prevent oil,...

    $26.70
    Add to Cart
  • 60 Series Windshield Wiper Motor Grommet (WMG-1)

    60 Series Windshield Wiper Motor Grommet

    If you have a 60 or 62 Series Land Cruiser and you noticed that your windshield wiper arms are super sloppy and you want to 'firm' them up, well this grommet gets you those anti-flaccid wiper arms you crave! Specifically this replaces the nylon grommet...

    $20.00
    Add to Cart
  • Door/Hood Plug (DHP-1)

    Door/Hood Plug

    This plug is used on a HUGE swath of Toyota vehicles as a hood and body drain port plug. On the 60s these are used in the pillars but are often time missing. If you notice water being trapped in the body or water on the floor of your 60 then its very...

    $2.30
    Add to Cart
  • Horn Contact Pin "Plate" (PIN-1)

    Horn Contact Pin "Plate"

    This OEM horn pin fits just about every Toyota on the road from 1974 til about 1990ish. The applications are too many to list. But if your horn uses this style of pin this is likely the one. The issue with the horn not working is very typically that this...

    $7.60
    Add to Cart
  • Overflow Tank Cap Gasket- 60/62/80 Series (OCG-1)

    Overflow Tank Cap Gasket- 60/62/80 Series

    Every get really frustrated with your 25+ year old 60/62/80 Series Land Cruiser and the fact that the radiator overflow cap doesn't fit snugly onto the bottle because the gasket just plain wore out? Then you find out the only way to get a replacement...

    $6.90
    Add to Cart
  • OEM Oil Filter-Medium 90915-40002 (OIL-2)

    OEM Oil Filter-Medium 90915-40002

    Medium Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). This is a slightly larger version of the smaller OEM Oil Filter-Small. If you want the larger made in Japan canisters you could try getting 15601-44011 but good...

    $13.90
    Add to Cart
  • Body Grease- Molykote 102 (BGM-102)

    Body Grease- Molykote 102

    This is the Toyota specific grease used in electrical motors on the Land Cruisers. Typical applications would be the windshield motors and the diff e-lock motors that commonly need to be rebuilt. One bottle is easily enough for two motor's worth of...

    $67.10
    Add to Cart
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  •  The most hated hose clamp for 5/8" hose (POO-1) 87124-28030

    The most hated hose clamp for 5/8" hose

    Quite possibly THE most hated hose clamp in the Land Cruiser world. Personally the use of these clamps makes me ill but they have their place. Since I get requests for them every now and again it seemed time to just start stocking for those that REALLY...

    $3.70
    Add to Cart
  • Not My Land Cruiser patch (WEP-3)

    Not My Land Cruiser More-Al patch

    So uh...yeah. Not sure which side of the topic you fall but now you can have a patch to state the obvious. :D Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT get some fancy backer artwork, these are meant to display not...

    $12.00
    Add to Cart
  • Complete Thermostat Kit for any 2F or 3F Engine (CTK-23)

    Complete Thermostat Kit for any 2F or 3F Engine

    Complete Thermostat Kit for any 2F or 3F Land Cruiser engine. There is one additional gasket (symmetrical opening) that is supplied and used for pre-11/1984 trucks. Post 11/1984 trucks use the asymmetrical gasket. This kit includes the 4 bolts that...

    $87.45
    Add to Cart
  • 60 Series Windshield Washer Tank Lid (WTL-1)

    60/62 Series Windshield Washer Tank Lid

    If you have a 60 or 62 Series Land Cruiser then there is a 99.999% chance that your windshield washer tank's lid is either dry rotted or is just simply missing. This is the OEM replacement for that lid. Part no: 85332-90A01 MADE in JAPAN

    $8.00
    Add to Cart
  • 60 Series Dome Light Lens (DLL-2)

    60 Series Dome Light Lens

    Dome light lens found on 80s and 90s Toyota Trucks and cars. Original is very likely either crumbling or very yellow or melted. Part no: 81241-20060 Fits:• Toyota 4Runner 1984-1995 • Toyota Land Cruiser 1981-1990 • Toyota Pickup 1984-1995...

    $9.50
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $38.45
    Add to Cart
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • 60 Series Land Cruiser Center Console Liner (CCL-1)

    60 Series Land Cruiser Center Console Liner

    NOTE: Liners are no longer screen printed. Image with logo is for display purposes only. When you look in the center console of your 60 Series Land Cruiser, do you ever feel as though there should be some kind of mat to prevent all of your crap from...

    $10.00
    Add to Cart
  • Land Cruiser Starter Mounting Stud- M12 (SMS-12)

    Land Cruiser Starter Mounting Stud- M12

    This is the starter mounting stud used on all 1FZFE, 2F, 3FE, F motors up to 1993. Part no. 90116-12005 This stud measures:• 43mm length• M12 x 1.25 x 18mm fine thread• M12 x 1.75 x 8mm course thread Made in USA

    $1.90
    Add to Cart
  • Block Drain Upgrade- 16mm plugs (BDU-2)

    Block Drain Upgrade- 16mm plugs

    This a different version of the stock drain cock used on early Land Cruisers, Pick-ups, 4Runners and other Toyota vehicles from the 70s and 80s. The original part number for the engine drain is: 96431-53828. The problem with this is its an open hole once...

    $14.75
    Add to Cart
  • Toyota Speedo Luber (LUB-1)

    Toyota Speedo-Luber

    NOTE: Only 10 in stock ready to ship. The rest will be on pre-order status.NOTE x2: This ONLY applies to those with an actual cable NOT a speed sensor #3FEMafia If you have a pre-93 Toyota Land Cruiser, or other Toyota 4WD truck with a speedometer...

    $51.00
    Add to Cart
  • Thermostat Bypass Hose and Clamps- F and 2F engines (TBH-2)

    Thermostat Bypass Hose and Clamps- F and 2F engines

    When you are replacing the thermostat, gasket and bolts on your F or 2F Land Cruiser motor, you also need to deal with the Bypass Hose that is off the thermostat hoses. This is a kit that has the hose and two clamps needed. This kit fits 1969-1987 FJ40s,...

    $24.20
    Add to Cart