null

200 Series Land Cruiser

  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $35.40
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • 80 Series Front U-Joint, fits most 4WD Toyota Trucks (FUJ-1)

    Front U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM front u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD  trucks. This is for one u-joint but its the same joint for front and rear of the FRONT driveshaft only. The rear shaft takes a different u-joint. While replacing...

    $71.65
    Add to Cart
  • Extended Handles for Seal Drive Tools- 18" (EXT-18)

    Extended Handles for Seal Drive Tools- 18"

    If you have a Toyota 4WD IFS truck than eventually your CV input seats WILL leak and if you don't install them correctly they WILL leak. In order to guarantee success you need the Toyota 4WD IFS Output Shaft Seal Driver but on the wider trucks (100...

    $80.00
    Add to Cart
  • OEM Automatic Transmission Drain Plug and Washer (ADP-1)

    OEM Automatic Transmission Drain Plug and Washer

    OEM replacement drain plug and washer for nearly all Automatic Transmission Toyota cars and trucks. Oddly enough this doesn't fit PRE-95 Land Cruisers. The main reason for changing this plug out with every drain and refill is to prevent galling the...

    $5.90
    Add to Cart
  • Toyota 4WD IFS Output Shaft Seal Driver (ASD-2)

    Toyota 4WD IFS Output Shaft Seal Driver

    Before starting this project you might want to give a watch to Timmy the Toolman's video about replacing these seals: Although used on all Toyota IFS, specifically on the 3rd Gen 4Runner there is a known issue with the needle bearings where the...

    $70.00
    Pre-Order Now
  • ScanGauge II Mounting Bracket (SMB-1)

    ScanGauge II Mounting Bracket

    If you have a vehicle with OBD2 then chances are you've considered an UltraGauge or better yet, a ScanGauge2 in order to see your ECU's vehicle parameters and check engine light (CEL) status. Once you decide you want a ScanGauge then comes the daunting...

    $64.00
    Pre-Order Now
  • 200 Series Thermostat and Housing Assembly (THA-1)

    200 Series Thermostat and Housing Assembly

    Thermostat and housing for the 200 Series Land Cruiser or Lexus LX570. Entire housing comes with integrated thermostat and o-ring. OEM part no: 16031-0S010 Fits the following vehicles:• 2008-2019 Land Cruiser• 2008-2019 Sequoia•...

    $49.65
    Add to Cart
  • 10-pack Steel Diff Plug washers (SDP-1)

    10-pack Steel Diff Plug washers

    OEM Toyota Drain Plug Gasket- steel for differentials. These are one-time use replacement washers used in OEM Magnetic Differential Plug Kit. Part no: 12157-10010 10-PK Made in JAPAN

    $15.00
    Add to Cart
  • 10-pack Aluminum Transfer Plug washers (ATP-2)

    10-pack Aluminum Transfer Plug washers

    OEM Toyota Drain Plug Gasket- aluminum for transfer cases and transmissions. These are one-time use replacement washers used in OEM Magnetic Transfer or Trans Case Drain Plug Kit Part no: 90430-A0003 10-PK Made in USA

    $17.40
    Add to Cart
  • 200 Series 3UR-FE Serpentine Drive Belt (TDB-5)

    200 Series 3UR-FE Serpentine Drive Belt

    OEM Serpentine Drive Belt for the 200 Series Land Cruisers with the 5.7L V8 3UR-FE gas motors. Fits the following vehicles:• 2008-2019 200 Series Land Cruiser or LX570• 2008-2019 Toyota Sequoia• 2007-2019 Toyota Tundra V8 Part no:...

    $59.50
    Add to Cart
  • Air Coupler and SB175 Bracket KIT (ACB-5KIT)

    Air Coupler and SB175 Bracket KIT

    The Air Coupler and SB175 Bracket KIT is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when...

    $130.00
    View Details
  • Air Coupler and SB175 Bracket (ACB-5) for On Board Air and Mounting the Anderson SB175 connector

    Air Coupler and SB175 Bracket

    This is the bracket that is ideal for anyone looking to mount both air and power on their vehicle. This bracket gives a safe/secure place to mount both the air coupler and the SB175 for hi-amperage power. MADE in USA

    $45.00
    View Details
  • Air Coupler and SB50 Bracket KIT (ACB-4KIT) for On Board Air and mounting the Anderson SB50

    Air Coupler and SB50 Bracket KIT

    The Air Coupler and SB50 Bracket KIT is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it...

    $95.00
    View Details
  • Air Coupler and SB50 Bracket (ACB-4) for On Board Air and Mounting the Anderson SB50 connector

    Air Coupler and SB50 Bracket

    The Air Coupler and SB50 Bracket is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it is...

    $40.00
    View Details
  • Air Coupler Bracket- guarded KIT (ACB-3KIT)

    Air Coupler Bracket- guarded KIT

    This Air Coupler Bracket Guarded KIT has everything you need for the last section of your On Board Air install. This KIT includes the coupler, the bulkhead, the air hose fittings, the guarded bracket, the hardware and 10ft of black nylon tubing. Simply...

    $68.00
    View Details
  • Air Coupler Bracket- Guarded (ACB-3) for On Board Air

    Air Coupler Bracket- Guarded

    The Guarded Air Coupler Bracket is designed for mounting in locations that you know it will be bumped or stepped on. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it is stepped on...

    $27.00
    View Details
  • Air Coupler Bracket- angled KIT (ACB-2KIT) for On Board Air

    Air Coupler Bracket- angled KIT

    This Air Coupler Bracket Angled KIT has everything you need for the last section of your On Board Air install. This is NOT the cheap Chinese stuff you can easily pick up at Harbor Freight. These are all top-of-the-line fittings. This KIT includes the...

    $64.00
    View Details
  • Air Coupler Bracket- Angled (ACB-2) for On Board Air

    Air Coupler Bracket- Angled

    This Air Coupler Bracket is ideal for mounting off the edge of a drawer system or mounting under a bumper or fender where a 90* angle is needed for preferred mounting positions. This angled Air Coupler Bracket is made from 1/8" thick 316 Stainless Steel...

    $20.00
    View Details
  • Air Coupler Bracket- flat (ACB-1)

    Air Coupler Bracket- flat

    This Air Coupler Bracket is ideal for mounting off the edge of a drawer system or mounting under a bumper or fender. This flat Air Coupler Bracket is made from 1/8" thick 316 Stainless Steel and then is powder coated black. Mounting hardware is also...

    $17.00
    View Details