null

On-Board-Air (OBA)

  • OEM Factory Locker Dial Kit for ARB Lockers (FLD-1KIT)

    OEM Factory Locker Dial Kit for ARB Lockers

    NOTE: Due to components getting harder to get please understand it could take many weeks before these can go out. Please be patient. If needed urgently its suggested you figure out your own solution using the schematic posted here. NOTE x2: this is...

    $85.00 - $140.00
    View Details
  • Three-Ear 1/4" NPT Aluminum Bulkhead Fitting (ABF-14)

    Three-Ear 1/4" NPT Aluminum Bulkhead Fitting

    NOW SHIPPING! Bulkhead fittings are soooooo boring, ugh :( It was time to change up the bulkhead use for On-Board-Air (OBA). your typical bulkhead is simple, utilitarian, and as unsexy as they come. Typical air fitting bulkheads are NPT threaded on...

    $25.00
    Choose Options
  • Irwin UniBit-4 Step Drill (IUB-4)

    Irwin UniBit-4 Step Drill

    Irwin UnitBit #4 used for step drilling larger holes used for On-Board-Air applications and for drilling the AN bung for the Turbo Drain Fitting. Sizes Included: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8" Made in USA

    $46.00
    Add to Cart
  • Milton M-Series Fitting Air Coupler Pacifier (ACP-M)

    Milton M-Series Fitting Air Coupler Pacifier

    After finding out the hard way that the standard Wits' End Pacifiers work with ALL air couplers EXCEPT ARB and Milton *eye roll*, needed to go back to the drawing board to redesign a plug that works specifically with the Milton M-series design. Now you...

    $20.00 - $26.00
    Choose Options
  • Anderson SB175 Environmental Boot- Load Side (AEB-175L) 
*Note that SOURCE is indicated for photo only

    Anderson SB175 Environmental Boot- Load Side

    These Anderson Environmental Boots are keyed as either SOURCE or LOAD sides. Use SOURCE on the cable side that is directly connected to your battery or power source. Use LOAD one the cable side of the device/accessory that you are looking to plug in to...

    $17.00
    View Details
  • 1.5in, 0-200PSI Gauge, 1-8NPT Back Mount (OBA-200-1-8B)

    1.5in, 0-200PSI Gauge, 1-8NPT Back Mount

    Liquid filled pressure gauges are perfect for On-Board-Air (OBA) applications. The glycerin liquid inside enhances reliability and readability of the gauges by dampening the effect of vibration and pulsation which is very common on an OBA setup where a...

    $13.00
    Add to Cart
  • 2in, 0-160PSI Gauge, 1-4NPT Bottom Mount (OBA-160-1-4L)

    2in, 0-160PSI Gauge, 1-4NPT Bottom Mount

    Liquid filled pressure gauges are perfect for On-Board-Air (OBA) applications. The glycerin liquid inside enhances reliability and readability of the gauges by dampening the effect of vibration and pulsation which is very common on an OBA setup where a...

    $14.00
    Add to Cart
  • Thread Sealant 59214

    Thread Sealant 59214

    Locks and seals threaded. Fittings, while resisting leakage, vibration loosening, moisture, hydraulic fluids and diesel fuels. Lubricates threads for easy assembly and disassembly. Wont shred or wear like tape. Parts may be repositioned up to 4 hours...

    $6.00
    Add to Cart
  • ARB Fitting Air Coupler Pacifier (ACP-ARB)

    ARB Fitting Air Coupler Pacifier

    After finding out the hard way that the standard Wits' End Pacifiers work with ALL air couplers EXCEPT ARB *eye roll*, needed to go back to the drawing board to redesign a plug that works specifically with the ARB design. The problem is its a non-US...

    $20.00 - $26.00
    Choose Options
  • Air Manifold- 6 port, 1/4in NPT (AMM-6)

    Air Manifold- 6 port, 1/4in NPT

    This 6-port billet aluminum manifold features (6) 1/4-inch NPT female ports to allow extra ports to any OBA system. Used to connect compressors, air lockers, or other pneumatic items, the manifold is black anodized for long-lasting good looks and will...

    $22.50
    Add to Cart
  • Quick Connect Air Coupler Plugs (ACP)

    Quick Connect Air Coupler Pacifier

    The Wits’ End Air Coupler Pacifier (aka Binky, aka "plug"). After spending far more time than I care to admit, I could NOT find an off-the-shelf solution for a quick disconnect air coupler plug. Sure there are caps that cover the entire coupler...

    $20.00 - $23.00
    Choose Options
  • 80 Series York discharge hose KIT (YRK-14)

    80 Series York discharge hose KIT

    Getting the York 210 mounted to your 1FZ Land Cruiser is only half the battle. Next you have to plumb it. The suction line is the first component but then you need the discharge hose kit next to get you from the York to the coalescing filter. This hose...

    $70.00
    Add to Cart
  • 80 Series OBA Coalescing Filter & Mount Kit (OBA-2KIT)

    80 Series OBA Coalescing Filter & Mount Kit

    When running a York On-Board-Air (OBA) system its always advisable to run a coalescing filter inline from the York's discharge line. The reason for this is to separate both the oil (coming from the York) and the condensation (created from the...

    $140.00
    Add to Cart
  • Air Quick Coupler Fitting Set (AQC-1)

    Air Quick Coupler Fitting Set

    For those just needing the Air Quick Coupler Fittings to get air from their air source to the air hose, here is everything you need. So long as you have a 3/4" hole you can mount this coupler kit. Just connect any 3/8" O.D. nylon hose and you are good to...

    $75.00
    Add to Cart
  • 80 Series Filter to Air Manifold hose KIT (YRK-13)

    80 Series Filter to Air Manifold hose KIT

    One of the pressurized hoses needed for installing the York OBA system onto your 80 Series is the compression hose going from the coelescing filter to the air manifold on the 80 Series with the 1FZ. This KIT has everything you need to connect the filter...

    $70.00
    Add to Cart
  • York 1/2in. AN pass-thru fitting (YRK-9)

    1FZ 1/2in. AN pass-thru fitting

    This is the second side of the fittings needed for the suction side hose on the York OBA install on the 1FZ motors found on the 80 Series Land Cruisers. There is a small hole that needs to be drilled into the air filter canister that allows this fitting...

    $31.00
    Add to Cart
  • 80 series York compressor mounting bracket (YRK-12)

    80 series York compressor mounting bracket

    For anyone considering mounting a York 209 or 210 onto your 80 Series Land Cruiser, you first need this bracket. This 1/4" zinc plated steel bracket is designed to mount on the 1FZ's aluminum head and places the York's fittings putting straight up. This...

    $210.00
    Add to Cart
  • York 90deg to 1/2in. AN fitting adaptor (YRK-8)

    York 90deg to 1/2in. AN fitting adaptor

    *NOTE: product shipping 1/15 One of the biggest challenges, after finding a solution for mounting a York 210 compressor to your vehicle, is to find a workable solution to making hoses for the fresh air suction line and the high-pressure discharge line...

    $40.00
    Add to Cart
  • 80 Series York suction hose (YRK-10)

    80 Series York suction hose KIT

    When you finally get the York 210 installed onto your 1FZ powered 80 Series Land Cruiser, you will need to get fresh air from somewhere to supply for the suction side. This KIT has everything you need to get the hose installed. All you need to do is...

    $82.00
    Add to Cart
  • Toyota Idler Pulley for 1FZ York OBA (TIP-1)

    Toyota Idler Pulley for 1FZ, AC or York OBA

    This is a Genuine Toyota Idler Pulley commonly used for the York On-Board-Air kits using on the 80 Series Land Cruiser and other vehicles. Its also the Air Conditioning idler pulley for the 1FZ motors. Part no. 88440-26090 MADE in JAPAN 

    $36.75
    Add to Cart
  • 80 Series 3-Groove Water Pump Pulley (WPP-1)

    80 Series 3-Groove Water Pump Pulley

    Note: This may fit other applications other than the 1FZ but its intended application is the 1FZ. Any usage outside of the 1FZ for the York OBA is outside of the scope of the design and there is no warranty. On the 1FZ powered 80 Series Land Cruisers...

    $165.00
    View Details
  • Toyota belt for the 80 Series York OBA (TBY-1)

    Toyota belt for the 80 Series York OBA

    If you have installed the Wits' End produced York OBA kit you already have one of these belts that came with the kit. This is the replacement for that belt and should be part of the belt replacement rotation as you would do with all of your other belts...

    $19.00
    Add to Cart
  • York On-Board-Air Bracket and Pulley Kit (YRK-1)

    York On-Board-Air Bracket and Pulley Kit

    FAQs: York On Board Air Kit The York OBA (On Board Air) mounting kit contains the basic components needed to mount the York 210 onto the 1FZ motor. Included: • Steel York Bracket with yellow zinc coating • Water Pump Pulley in billet aluminum...

    $420.00
    View Details
  • 1/4" NPT Splitter for 3/8" Nylon tubing (NOR-4)

    1/4" NPT Splitter for 3/8" Nylon tubing

    This is ideal for splitting the line to split from front to rear of the vehicle. The 3/8" ends are push-to-connect fitting for 3/8" nylon tubing and the threaded end is 1/4NPT. It doesn't get any easier to use; just make a clean cut on the tubing and...

    $12.00
    Add to Cart
  • 1/4NPT OBA Tank Drain Side Pull (OBA-14DP)

    1/4NPT OBA Tank Drain Side Pull

    1/4" Air Compressor Valve Tank Moisture Pull Drain W/ 60" cable to drain excess fluid from compressor tank. If you are running an air tank as part of your OBA setup then you MUST have a drain or rust is virtually guaranteed and you run the risk of...

    $13.00
    Add to Cart
  • 1/2 Barb to 8AN 90deg Fitting (OBA-8AN-12BR)

    1/2 Barb to 8AN 90deg Fitting

    Precision made, high quality AN to NPT adapters are ideal for the delivery of fuel, oil, water, air, or any fluid of your choice. CNC Machined using lightweight 6061 aluminum and anodized black. These fitting has many applications but for...

    $25.00
    Add to Cart
  • 3/8in NPT to 8AN Fitting Adapter (OBA-38NPT-8AN)

    3/8in NPT to 8AN Fitting Adapter

    Precision made, high quality AN to NPT adapters are ideal for the delivery of fuel, oil, water, air, or any fluid of your choice. CNC Machined using lightweight 6061 aluminum and anodized black. This fitting has many applications but for...

    $15.00
    Add to Cart
  • Nylon 11, 3/8" tubing-black, 10ft (NOR-38B)

    Nylon 11, 3/8" tubing-black, 10ft

    Nylon Tube Manufactured from Nylon 11 and spec'd to be used for all Wits' End OBA systems. Note: This is sold in 10ft sections BUT If you order 20ft, 30ft, 40ft, etc. sections will be shipped in one continuous roll. Features:• UL-94HB flame...

    $27.50
    Add to Cart
  • 1/4" NPT to 3/8" tube fitting (NOR-1)

    1/4" NPT to 3/8" tube fitting

    This is where everything kind of starts for running nylon tubing for On Board Air systems. The thread is your standard 1/4"NPT male and is threaded into air tanks, manifolds, quick couplers, etc. The 3/8" end is a push-to-connect fitting for 3/8" nylon...

    $8.00
    Add to Cart
  • 1/4" NPT, 3/8" tube, swivel elbow fitting (NOR-2)

    1/4" NPT, 3/8" tube, swivel elbow fitting

    This is where everything kind of starts for running nylon tubing for On Board Air systems. The thread is your standard 1/4"NPT male and is threaded into air tanks, manifolds, quick couplers, etc. The 3/8" end is a push-to-connect fitting for 3/8" nylon...

    $9.75
    Add to Cart
  • T-fitting for 3/8" Nylon tubing (NOR-3)

    T-fitting for 3/8" Nylon tubing

    This is ideal for splitting the line to split from front to rear of the vehicle. The 3/8" ends are push-to-connect fitting for 3/8" nylon tubing. It doesn't get any easier to use; just make a clean cut on the tubing and push into the fitting until it...

    $12.00
    Add to Cart