null

Tools

  • Toyota Speedo-Luber (LUB-1)

    Toyota Speedo-Luber

    NOTE: Only 10 in stock ready to ship. The rest will be on pre-order status.NOTE x2: This ONLY applies to those with an actual cable NOT a speed sensor #3FEMafia If you have a pre-93 Toyota Land Cruiser, or other Toyota 4WD truck with a speedometer...

    $51.00
    Pre-Order Now
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  • Extended Handles for Seal Drive Tools- 18" (EXT-18)

    Extended Handles for Seal Drive Tools- 18"

    If you have a Toyota 4WD IFS truck than eventually your CV input seats WILL leak and if you don't install them correctly they WILL leak. In order to guarantee success you need the Toyota 4WD IFS Output Shaft Seal Driver but on the wider trucks (100...

    $80.00
    Add to Cart
  • Toyota 4WD IFS Output Shaft Seal Driver (ASD-2)

    Toyota 4WD IFS Output Shaft Seal Driver

    Before starting this project you might want to give a watch to Timmy the Toolman's video about replacing these seals: Although used on all Toyota IFS, specifically on the 3rd Gen 4Runner there is a known issue with the needle bearings where the...

    $70.00
    Pre-Order Now
  • Irwin UniBit-4 Step Drill (IUB-4)

    Irwin UniBit-4 Step Drill

    Irwin UnitBit #4 used for step drilling larger holes used for On-Board-Air applications and for drilling the AN bung for the Turbo Drain Fitting. Sizes Included: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8" Made in USA

    $46.00
    Add to Cart
  • Overdrive Seal Tool Handle (OSH-1)

    Overdrive Seal Tool Handle

    To be perfectly honest I really didn't picture every bothering getting these made but funny enough I keep getting requests for one so here it is...the Oil Seal Overdrive Handle. This is just the Wits' End version of the same thing you can get from...

    $29.50
    Add to Cart
  • Wheel Stud Tool- 12mm Studs (WST-1)

    Wheel Stud Tool- 12mm Studs

    This tool all started because of this thread: RTH: stuck in Primm, wheel lugs sheered off All 6 wheel studs snapped while driving on the frwy coming home from Las Vegas at 60MPH. I was stuck with no way to replace the broken studs so I had to be towed...

    $55.00
    Pre-Order Now
  • OEM Steel Wheel Chock (SWC-1)

    OEM Steel Wheel Chock

    It should go without saying that ALL vehicles should have a pair of wheel chocks for safety. Every time you are repairing your truck or replacing a tire or anything that requires you to be under it, a wheel chock is a must. If you have a pair of wheel...

    $26.00
    Add to Cart
  • 1FZ SuperCharger Wrench (SCW-1)

    1FZ SuperCharger Wrench

    This is a custom designed wrench developed by Tools R Us (Kevin R.I.P.) for the 1FZ SuperCharged engines. This tool is a MUST when changing out or just removing the SuperCharger's serpentine belt by relaxing the tensioner pulley. MADE in USA

    $40.00
    Add to Cart
  • 80 Series Inner Axle Seal Offset Driver (ASD-1)

    80 Series Inner Axle Seal Offset Driver

    There is one thing that comes as a right of passage in owning an 80 Series and that is the rebuilding of our front knuckles. Generally speaking its not terribly technical, just messy and takes along time. Especially the first time. But there can be...

    $34.00
    Pre-Order Now
  • Connector Pin Tool-basic (PST-2)

    Connector Pin Tool-basic

    If you own any Toyota long enough you will eventually need to either modify or repair an electrical connector. This can be daunting because it seems everyone is already having a hard enough time building up the courage to even commit to "cutting the...

    $43.00
    Pre-Order Now
  • Prison Shank- Connector Pin Tool (PST-1)

    Prison Shank- Connector Pin Tool

    If you own any Toyota long enough you will eventually need to either modify or repair an electrical connector. This can be daunting because it seems everyone is already having a hard enough time building up the courage to even commit to "cutting the...

    $52.00
    Pre-Order Now
  • Bushing Press Tool- KIT (BPT-1)

    Bushing Press Tool- KIT

    The Bushing Press Tool Kit has all of the press tools needed to press every suspension bushing found on the 80 Series Land Cruiser regardless of year. These tools are made from steel and are sure to last through MANY installations. Includes:•...

    $265.00
    Pre-Order Now
  • Bushing Press Tool- 39mm (BPT-39)

    Bushing Press Tool- 39mm

    **In production now. Next batch expected to ship by 10/31/2022** The 39mm Bushing Press Tool is used to press out the old front or rear panhard bushings in the 80 Series Land Cruisers in order to press in new OEM bushings. A serious press is in order,...

    $56.00
    View Details
  • Bushing Press Tool- 49mm (BPT-49)

    Bushing Press Tool- 49mm

    **In production now. Next batch expected to ship by 10/31/2022** The 49mm Bushing Press Tool is used to press out the old rear upper control arm bushings in 80 Series Land Cruisers in order to press in new OEM bushings. A serious press is in order, of...

    $65.00
    View Details
  • Bushing Press Tool- 53mm (BPT-53)

    Bushing Press Tool- 53mm

    **In production now. Next batch expected to ship by 10/31/2022** The 53mm Bushing Press Tool is used to press out the old REAR of the lower control arm bushings in the 80 Series Land Cruisers in order to press in new OEM bushings. A serious press is in...

    $65.00
    View Details
  • Bushing Press Tool- 60mm (BPT-60)

    Bushing Press Tool- 60mm

    **In production now. Next batch expected to ship by 1/9/2023** The 60mm Bushing Press Tool is used to press out the old front lower control arm bushings in 80 Series Land Cruisers in order to press in new OEM or other poly/caster correction bushings...

    $70.50
    View Details
  • Toyota Diesel Power Steering Pump Gear Handle (PGH-2)

    Toyota Diesel Power Steering Pump Gear Handle

    When you are removing the gear driven power steering pump from a Toyota Diesel motor to rebuild, you will need to remove the gear. The gear needs to be held in place while the nut is impacted off. Holding the gear meant two options: Put the gear in a...

    $24.00
    Add to Cart
  • 80 Series 1FZ Power Steering Pump Gear Handle (PGH-1)

    80 Series 1FZ Power Steering Pump Gear Handle

    When you are removing the gear driven power steering pump from the 1FZ motor to rebuild, you will need to remove the gear. The gear needs to be held in place while the nut is impacted off. Holding the gear meant two options: Put the gear in a vice (which...

    $24.00
    Add to Cart