null

70 Series HD Land Cruiser (up to 1/90)

  • Toyota Magnetic Differential Plug Kit (DPK-1)

    OEM Magnetic Differential Plug Kit

    These OEM Magnetic Differential Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs with M18 threads. These are the hex plugs that replace the easily damaged diff fill and drain plugs. The originals can be easily damaged from off-roading or from a...

    $11.45
    Add to Cart
  • Gates Green Stripe heater hose 5/8" by the foot (GAT-58)

    Gates Green Stripe heater hose 5/8" by the foot

    Although its not OEM its the next best thing to replace the direct runs of heater hose in your truck. Note: the quantity selected will be in a single length of hose Features:• Green Stripe® construction provides best cost-per-mile...

    $3.25
    Add to Cart
  • OEM Magnetic Transfer or Trans Case Drain Plug Kit (DPK-2)

    OEM Magnetic Transfer or Trans Case Drain Plug Kit

    These OEM Magnetic Transfer Case Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs (does not fit the FJ Cruiser auto). These are the hex plugs that replace the easily damaged drain plugs. The originals can be easily damaged from a tool rounding out...

    $11.90
    View Details
  • Oil Drain Bolt Gasket (ODG-10)

    Oil Drain Bolt Gasket

    There are your standard Toyota drain plug gaskets that should be replaced with every oil change. Part no: 90430-12031 Fits: Toyota FJ Cruiser 2007-2014 Toyota Land Cruiser 1991 - 2020 Toyota Pickup 1990 - 1995 Toyota Sequoia 2001-2020 Toyota T100...

    $10.45
    Add to Cart
  • Gates Green Stripe heater hose 1/2" by the foot (GAT-12)

    Gates Green Stripe heater hose 1/2" by the foot

    Although its not OEM its the next best thing to replace the direct runs of heater hose in your truck. Note: the quantity selected will be in a single length of hose Features:• Green Stripe® construction provides best cost-per-mile...

    $3.00
    Add to Cart
  • Land Cruiser Shock Bolt and Washer (SBW-1)

    Land Cruiser Shock Bolt and Washer

    These are the shock bolts that are used in several models of Land Cruiser. These tend to not only rust out but they also tend to get damaged during off-roading. Part no: 90119-12088• 60/62 series: rear upper and lower, front lowers (6 needed)•...

    $3.70
    Add to Cart
  • 80 Series Wheel Stud- Rear (STD-2)

    60/80 Series Wheel Stud- Rear

    OEM rear wheel stud for all 60 and 80 Series Land Cruisers. Part no: 90942-02052 Also fits:• 1981-1997 Toyota Land Cruiser• 1984-2000 Toyota 4Runner• 1979-1995 Toyota Pickup• 2001-2007 Toyota Sequoia• 1993-1998 Toyota...

    $6.75
    Add to Cart
  • OEM 25mm Spring and Bolt Clamp for 3/4" hoses (SBC-25)

    OEM 25mm Spring and Bolt Clamp for 5/8" ID hoses

    On the 80 Series 3FE and 1FZ engines, all of the heater hoses are secured by a spring steel clamp that is tightened at the factory using a cotter pin and tool to lock it into place. These are intended as single use clamps. If you still have these clamps...

    $0.50
    Add to Cart
  • OEM Washable Cyclonic Air Filter (AIR-1)

    OEM Washable Cyclonic Air Filter

    OEM washable air filter that works for the 80 Series 3FE and 1FZ but also the heavy duty 7x series and diesel motors with the cyclonic air filter housing. Yes, the filter is washable and reusable. Part no: 17801-61030 Made in JAPAN

    $27.90
    Add to Cart
  • Toyota FIPG 103 Adhesive (TOY-103) 00295-00103

    Toyota FIPG 103 Adhesive

    TOYOTA OEM specified adhesive for the oil pan and camshaft housing. Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings. OEM part # 00295-00103 • Assemble parts within 15...

    $18.00
    View Details
  • Fuel Injector Connector Housing (FIC-1)

    Fuel Injector Connector Housing

    Original Toyota Sumitomo 2 Way TS Plug Housing for Denso Injectors. Connector ONLY. Terminals not included. These connectors are ALWAYS brittle and tend to break after 20+ years on our trucks. They seem to want to break at the most inopportune time. You...

    $10.60
    Add to Cart
  • 80 Series OEM Rubber Exhaust Bushing (REB-1)

    80 Series OEM Rubber Exhaust Bushing Kit

    Note: Price INCLUDES the four nuts required Trying to track down that annoying clunk when you go over a speed bump or going up a driveway? Have you checked your exhaust hangers? Your 80 Series Land Cruiser has three of them and their purpose is to...

    $28.75
    Add to Cart
  • 10-pack Steel Diff Plug washers (SDP-1)

    10-pack Steel Diff Plug washers

    OEM Toyota Drain Plug Gasket- steel for differentials. These are one-time use replacement washers used in OEM Magnetic Differential Plug Kit. Part no: 12157-10010 10-PK Made in JAPAN

    $15.00
    Add to Cart
  • 80 series 1FZ Alternator Adjusting Bolt (AAB-2)

    80 series 1FZ Alternator Adjusting Bolt

    This is the OEM alternator adjusting bolt found on all 80 Series Land Cruisers with the 3FE and 1FZ motors. This bolt is commonly broken or stripped because the locking bolt on the adjuster block wasn't loosened first. Also fits: Land Cruisers with a...

    $2.79
    Add to Cart
  • 80 Series Driveshaft Hardware Kit-Rear 11mm (DCS-3)

    80 Series Driveshaft Hardware Kit-Rear 11mm

    This is the complete driveshaft hardware for most Land Cruisers on the road. This kit replaces the washer/nut on the transfer case side and the bolt/washer/nut on the differential side. The 11mm rear driveshaft hardware fits:• All FJ60 Series Land...

    $32.70
    Add to Cart
  • Connector Pin Tool-basic (PST-2)

    Connector Pin Tool-basic

    If you own any Toyota long enough you will eventually need to either modify or repair an electrical connector. This can be daunting because it seems everyone is already having a hard enough time building up the courage to even commit to "cutting the...

    $43.00
    View Details
  • 10-pack Aluminum Transfer Plug washers (ATP-2)

    10-pack Aluminum Transfer Plug washers

    OEM Toyota Drain Plug Gasket- aluminum for transfer cases and transmissions. These are one-time use replacement washers used in OEM Magnetic Transfer or Trans Case Drain Plug Kit Part no: 90430-A0003 10-PK Made in USA

    $18.35
    Add to Cart
  • OEM Steel Wheel Chock (SWC-1)

    OEM Steel Wheel Chock

    It should go without saying that ALL vehicles should have a pair of wheel chocks for safety. Every time you are repairing your truck or replacing a tire or anything that requires you to be under it, a wheel chock is a must. If you have a pair of wheel...

    $26.70
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • OEM Automatic Transmission Drain Plug and Washer (ADP-1)

    OEM Automatic Transmission Drain Plug and Washer

    OEM replacement drain plug and washer for nearly all Automatic Transmission Toyota cars and trucks. Oddly enough this doesn't fit PRE-95 Land Cruisers. The main reason for changing this plug out with every drain and refill is to prevent galling the...

    $6.80
    Add to Cart
  • Wits' End patch (WEP-1)

    Wits' End patch

    The Wits' End more-al patch. Add one to your collection or start a collection today. More-al patches are fun as you display your interest to your peers and draw on that common bond of TEQ in the Land Cruiser community. Oh and no cheap Chinese junk,...

    $9.00
    Add to Cart
  • Check Yer Nuts More-Al patch (WEP-4)

    Check Yer Nuts More-Al patch

    If you have an 80 Series then you SHOULD know about the utter importance of checking your nuts! Specifically your knuckle stud hardware. Here's a patch to help remind you. Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT...

    $12.00
    View Details
  • DashHole Plug- Mount, with Notch (DPM-2) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, with Notch

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    View Details
  • 11mm Driveshaft Bolt- Spare (DCS-11)

    11mm Driveshaft Bolt- Spare

    Individual OEM 11mm driveshaft bolt. Although you can get an entire 10mm driveshaft hardware or 11mm driveshaft hardware kit, sometimes it helps to have a few 11mm bolts as a spare.

    $1.50
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • Wheel Stud Tool- 12mm Studs (WST-1)

    Wheel Stud Tool- 12mm Studs

    This tool all started because of this thread: RTH: stuck in Primm, wheel lugs sheered off All 6 wheel studs snapped while driving on the frwy coming home from Las Vegas at 60MPH. I was stuck with no way to replace the broken studs so I had to be towed...

    $55.00
    Add to Cart
  • Inner Axle Seal, Front- 70/80 Series (IAS-1)

    Inner Axle Seal, Front- 70/80 Series

    Inner axle seal for the 80 Series Land Cruisers. Also fits the 70 Series and 105 Series. If you have a groove on the journal of the inner axle shaft then you can overdrive seal using the 80 Series Inner Axle Seal Offset Driver. Part no:...

    $9.60
    Add to Cart
  • Rear U-Joint 4WD Toyota Trucks, 70/80/100/200 (FUJ-2)

    Rear U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM rear u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD HD trucks. This is for one u-joint but its the same joint for front and rear of the REAR driveshaft only. The front shaft takes a different u-joint. While replacing the...

    $70.70
    Add to Cart
  • Toyota FIPG 1281 Adhesive (TOY-1281)

    Toyota FIPG 1281 Adhesive

    TOYOTA OEM specified RED adhesive for the transmission pan. Formed-in-Place Transmission Gasket is a high-performance RTV silicone used as a formed-in-place transmission gasket to seal various flange and large clearance surfaces in order to prevent oil,...

    $26.70
    Add to Cart
  • 80 Series Front U-Joint, fits most 4WD Toyota Trucks (FUJ-1)

    Front U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM front u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD  trucks. This is for one u-joint but its the same joint for front and rear of the FRONT driveshaft only. The rear shaft takes a different u-joint. While replacing...

    $71.70
    Add to Cart
  • Horn Contact Pin "Plate" (PIN-1)

    Horn Contact Pin "Plate"

    This OEM horn pin fits just about every Toyota on the road from 1974 til about 1990ish. The applications are too many to list. But if your horn uses this style of pin this is likely the one. The issue with the horn not working is very typically that this...

    $7.60
    Add to Cart
  • Body Grease- Molykote 102 (BGM-102)

    Body Grease- Molykote 102

    This is the Toyota specific grease used in electrical motors on the Land Cruisers. Typical applications would be the windshield motors and the diff e-lock motors that commonly need to be rebuilt. One bottle is easily enough for two motor's worth of...

    $67.10
    Add to Cart
  • DashHole Plug- Mount, Notch-Free Face (DPM-1) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, Notch-Free

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Add to Cart
  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  •  The most hated hose clamp for 5/8" hose (POO-1) 87124-28030

    The most hated hose clamp for 5/8" hose

    Quite possibly THE most hated hose clamp in the Land Cruiser world. Personally the use of these clamps makes me ill but they have their place. Since I get requests for them every now and again it seemed time to just start stocking for those that REALLY...

    $3.70
    Add to Cart
  • Not My Land Cruiser patch (WEP-3)

    Not My Land Cruiser More-Al patch

    So uh...yeah. Not sure which side of the topic you fall but now you can have a patch to state the obvious. :D Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT get some fancy backer artwork, these are meant to display not...

    $12.00
    Add to Cart
  • Gates heater hose 5/16" by the foot (GAT-516)

    Gates heater hose 5/16" by the foot

    Although its not OEM its the next best thing to replace the direct runs of heater hose in your truck. This is equivelant to 8mm coolant hose found on some Toyota Diesel trucks and especially the 1FZ engine with the added supercharger.  Note: the...

    $2.50
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $38.45
    Add to Cart
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • Toyota Speedo Luber (LUB-1)

    Toyota Speedo-Luber

    NOTE: Only 10 in stock ready to ship. The rest will be on pre-order status.NOTE x2: This ONLY applies to those with an actual cable NOT a speed sensor #3FEMafia If you have a pre-93 Toyota Land Cruiser, or other Toyota 4WD truck with a speedometer...

    $51.00
    Add to Cart
  • Toyota Diesel Power Steering Pump Gear Handle (PGH-2)

    Toyota Diesel Power Steering Pump Gear Handle

    When you are removing the gear driven power steering pump from a Toyota Diesel motor to rebuild, you will need to remove the gear. The gear needs to be held in place while the nut is impacted off. Holding the gear meant two options: Put the gear in a...

    $24.00
    Add to Cart
  • Dual Fuel Tank Lever Knob (DTK-1)

    Dual Fuel Tank Lever Knob

    Replacement dual tank fuel knobs for 77324-60011 and 77324-60012 which are now obsolete. Commonly found on nearly all Land Cruisers with a fuel door tank selector knob. The original from Toyota is made from Bakelite and is either gone or cracked...

    $27.50
    Add to Cart
  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • 15% Overdrive Machined Alt Pulley (OMP-1)

    15% Overdrive Machined Alt Pulley, 1FZ

    NOTE: FITS ANY 1FZ LAND CRUISER ONLY Is this required for your 1FZ Land Cruiser? No. But if you spend a lot of time sitting at or close to idle on the freeway in traffic, or slowly crawling up a hill, or idling at a parking lot trying to charge the...

    $162.50
    Add to Cart