null

5th Gen 4Runner (10'-17')

  • Modified 54mm Hub Nut Tool (HUB-2)

    Modified 54mm Hub Nut Tool- V2

    This is a new 1/2" drive 54mm socket that has been CNC machined to add 3 notches for use on the full float rear wheel bearing nut.  This single tool can be used to loosen/torque the front and the rear axle wheel bearing nuts. The interior of the nut...

    $55.00
    Add to Cart
  • OEM Toyota Windshield Washer Fluid- 1QT (WWF-1)

    OEM Toyota Windshield Washer Fluid- 1QT

    NOTE: Due to the flammable, liquid contents this item (and everything else in the order shipped with it) MUST go ground shipping. OEM Toyota windshield washer fluid in one qrt container. Part number 00475-00WWF

    $9.75
    Add to Cart
  • OEM Wire Harness Tape (WHT-1)

    OEM Wire Harness Tape

    This is the OEM wire harness tape used on the Toyota Land Cruiser. This is the ideal wrap tape for under the hood. For harness tape that runs along the inside of body panels its preferred to use TESSA tape for it helps reduce noise during vibration...

    $35.40
    Add to Cart
  • 90915-YZZD3 OEM Oil Filter (OIL-1)

    OEM Oil Filter-Small

    Small Toyota oil filter for use on the 1FZ and 2UZ Land Cruiser engines (and plenty others). If you want the larger made in Japan canisters you could try getting 15601-44011. Part no. 90915-YZZD3 MADE in THAILAND

    $5.10
    Add to Cart
  • Emergency Brake Line Plug- M10 x 1.0 (BLP-1)

    Emergency Brake Line Plug- M10 x 1.0

    EMERGENCY USE ONLY!!!   Ever been on a trail or water crossing and had a branch or rock smash a brake hard line or literally have the brake hose ripped in half? I've had the displeasure of dealing with it twice in 35 years; once used a pair of...

    $25.00
    Add to Cart
  • Toyota OEM Brake Caliper Grease (BCG-1)

    Toyota OEM Brake Caliper Grease

    OEM Toyota disc brake grease that is used for grease the caliper pieces that see metal to metal contact. This would be on the faces or the brake pad shims and where the brake clips comes into contact with pad. For metal to rubber grease use Lithium Soap...

    $28.80
    Add to Cart
  • Lithium Soap Based Glycol Grease

    Lithium Soap Based Glycol Grease

    Ever open up your Factory Service Manual, and while thumbing thru the brake section, and notice the words "Lithium Soap Based Glycol Grease"? Well THIS is that grease.  Think of it this way, if a rubber piece touches ANYTHING metal, use this grease...

    $9.75
    Add to Cart
  • 80/100 Series Transfer Indicator Switch (TIS-1)

    80/100 Series Transfer Indicator Switch

    On the 80 Series Land Cruiser this is used For the Transfer Indicator Switch No. 1 and No. 3. This should be the first check when you can't get the lockers to light up on the dash. These commonly go bad but they can be sprayed with brake clean and...

    $97.85
    Add to Cart
  • Rear U-Joint 4WD Toyota Trucks, 70/80/100/200 (FUJ-2)

    Rear U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM rear u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD HD trucks. This is for one u-joint but its the same joint for front and rear of the REAR driveshaft only. The front shaft takes a different u-joint. While replacing the...

    $70.80
    Add to Cart
  • 80 Series Front U-Joint, fits most 4WD Toyota Trucks (FUJ-1)

    Front U-Joint 4WD Toyota Trucks, 70/80/100/200

    OEM front u-joint for the 80 Series Land Cruiser although it will fit most Toyota 4WD  trucks. This is for one u-joint but its the same joint for front and rear of the FRONT driveshaft only. The rear shaft takes a different u-joint. While replacing...

    $71.65
    Add to Cart
  • Yellow Tab Hose Clamp (HCY-1)

    Hose Clamp- Yellow Tab for 2F and Diesel Engines

    OEM radiator hose clamp commonly used on many Land Cruiser diesel engines, Tacoma, 4Runner and T100 engines. Also commonly found on the 2F radiator side lower hose. This is the clamp with the "yellow" marking tab.  Part no: 96111-10530 MADE in...

    $5.05
    Add to Cart
  • Extended Handles for Seal Drive Tools- 18" (EXT-18)

    Extended Handles for Seal Drive Tools- 18"

    If you have a Toyota 4WD IFS truck than eventually your CV input seats WILL leak and if you don't install them correctly they WILL leak. In order to guarantee success you need the Toyota 4WD IFS Output Shaft Seal Driver but on the wider trucks (100...

    $80.00
    Add to Cart
  • OEM Automatic Transmission Drain Plug and Washer (ADP-1)

    OEM Automatic Transmission Drain Plug and Washer

    OEM replacement drain plug and washer for nearly all Automatic Transmission Toyota cars and trucks. Oddly enough this doesn't fit PRE-95 Land Cruisers. The main reason for changing this plug out with every drain and refill is to prevent galling the...

    $5.90
    Add to Cart
  • DashHole Plug- Mount, with Notch (DPM-2) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, with Notch

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Pre-Order Now
  • DashHole Plug- Mount, Notch-Free Face (DPM-1) Fits all 80s and 90s Toyota vehicles and Delta Console

    DashHole Plug- Mount, Notch-Free

    This comes from the "why didn't I do this early" pile. Every single Toyota car and truck from the 80's and 90's had them, switch blanks. You'd often wonder, "I wonder what Toyota had planned to install there?" Only to never find out. Just staring...

    $40.00
    Add to Cart
  • 80/100 Series ABS Sensor Delete Plugs- Rear (ABS-3)

    80/100 Series ABS Sensor Delete Plugs- Rear

    NOTE: Deleting your ABS is NOT recommended but many still do it for a myriad of reasons. Off-Road brake control and axle conversions are two reasons. Use at your own risk. This is been on my “to do” list for a pretty long time. For those...

    $48.00
    Pre-Order Now
  • Toyota 4WD IFS Output Shaft Seal Driver (ASD-2)

    Toyota 4WD IFS Output Shaft Seal Driver

    Before starting this project you might want to give a watch to Timmy the Toolman's video about replacing these seals: Although used on all Toyota IFS, specifically on the 3rd Gen 4Runner there is a known issue with the needle bearings where the...

    $70.00
    Pre-Order Now
  • ScanGauge II Mounting Bracket (SMB-1)

    ScanGauge II Mounting Bracket

    If you have a vehicle with OBD2 then chances are you've considered an UltraGauge or better yet, a ScanGauge2 in order to see your ECU's vehicle parameters and check engine light (CEL) status. Once you decide you want a ScanGauge then comes the daunting...

    $64.00
    Pre-Order Now
  • 10-pack Steel Diff Plug washers (SDP-1)

    10-pack Steel Diff Plug washers

    OEM Toyota Drain Plug Gasket- steel for differentials. These are one-time use replacement washers used in OEM Magnetic Differential Plug Kit. Part no: 12157-10010 10-PK Made in JAPAN

    $15.00
    Add to Cart
  • 10-pack Aluminum Transfer Plug washers (ATP-2)

    10-pack Aluminum Transfer Plug washers

    OEM Toyota Drain Plug Gasket- aluminum for transfer cases and transmissions. These are one-time use replacement washers used in OEM Magnetic Transfer or Trans Case Drain Plug Kit Part no: 90430-A0003 10-PK Made in USA

    $17.40
    Add to Cart
  • Body Grease- Molykote 102 (BGM-102)

    Body Grease- Molykote 102

    This is the Toyota specific grease used in electrical motors on the Land Cruisers. Typical applications would be the windshield motors and the diff e-lock motors that commonly need to be rebuilt. One bottle is easily enough for two motor's worth of...

    $58.75
    Add to Cart
  • Block Drain Upgrade- 14mm plugs (BDU-1)

    Block Drain Upgrade- 14mm plugs

    The proper way to drain your coolant is to also drain and flush your engine block. In order to do that you need to remove the drain plug on your block. The 2008-2019 Land Cruiser 200 Series, FJ Cruiser and 5th Gen 4Runners all had this drain plug in...

    $12.75
    Add to Cart
  • Toyota FIPG 1281 Adhesive (TOY-1281)

    Toyota FIPG 1281 Adhesive

    TOYOTA OEM specified RED adhesive for the transmission pan. Formed-in-Place Transmission Gasket is a high-performance RTV silicone used as a formed-in-place transmission gasket to seal various flange and large clearance surfaces in order to prevent oil,...

    $26.70
    Add to Cart
  • Toyota Truck ABS Sensor Delete Plugs- Front (ABS-2)

    Toyota Truck ABS Sensor Delete Plugs- Front

    NOTE: Deleting your ABS is NOT recommended but many still do it for a myriad of reasons. Off-Road brake control and axle conversions are two reasons. Use at your own risk. This is been on my “to do” list for a pretty long time. For those...

    $65.00
    Pre-Order Now
  • Toyota FIPG 103 Adhesive (TOY-103) 00295-00103

    Toyota FIPG 103 Adhesive

    TOYOTA OEM specified adhesive for the oil pan and camshaft housing. Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings. OEM part # 00295-00103 • Assemble parts within 15...

    $18.00
    Add to Cart
  • Oil Drain Bolt Gasket (ODG-10)

    Oil Drain Bolt Gasket

    There are your standard Toyota drain plug gaskets that should be replaced with every oil change. Part no: 90430-12031 Fits: Toyota FJ Cruiser 2007-2014 Toyota Land Cruiser 1991 - 2020 Toyota Pickup 1990 - 1995 Toyota Sequoia 2001-2020 Toyota...

    $10.15
    Add to Cart
  • Fuel Injector Connector Housing (FIC-1)

    Fuel Injector Connector Housing

    Original Toyota Sumitomo 2 Way TS Plug Housing for Denso Injectors. Connector ONLY. Terminals not included. These connectors are ALWAYS brittle and tend to break after 20+ years on our trucks. They seem to want to break at the most inopportune time. You...

    $9.30
    Add to Cart
  • 1FZ-FE More-Al patch (WEP-5)

    1FZ-FE More-Al patch

    If you have an 80 Series then you SHOULD know about the utter importance of showing your 1FZ pride. Have a 3FE? Its ok, there is a 1FZ for you out there somewhere I'm sure. ;) Oh and no cheap Chinese junk, these are made locally! Yes, the back has...

    $10.00
    View Details
  • Check Yer Nuts More-Al patch (WEP-4)

    Check Yer Nuts More-Al patch

    If you have an 80 Series then you SHOULD know about the utter importance of checking your nuts! Specifically your knuckle stud hardware. Here's a patch to help remind you. Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT...

    $12.00
    View Details
  • Not My Land Cruiser patch (WEP-3)

    Not My Land Cruiser More-Al patch

    So uh...yeah. Not sure which side of the topic you fall but now you can have a patch to state the obvious. :D Oh and no cheap Chinese junk, these are made locally! Note: No, these will NOT get some fancy backer artwork, these are meant to display not...

    $12.00
    Add to Cart
  • Suck It/Flip off More-Al patch (WEP-2)

    Suck It/Flip off More-Al Patch

    If you found this page from the IH8MUD forum, or most forums, then you're likely already familiar with the :flipoff2: emoticon. This is a simple more-al patch based on that. Use it in reference or use it to stick a thumb in the eye of your oppressor...

    $12.00
    View Details
  • Wits' End patch (WEP-1)

    Wits' End patch

    The Wits' End more-al patch. Add one to your collection or start a collection today. More-al patches are fun as you display your interest to your peers and draw on that common bond of TEQ in the Land Cruiser community. Oh and no cheap Chinese junk,...

    $9.00
    Add to Cart
  • TEQ More-Al Patch-red (TEQ-4)

    TEQ

    TEQ More-Al Patch-red

    No Toyota enthusiast should be without this TEQ  more-al patch. Add one to your collection or start a collection today.  More-al patches are fun as you display your interest to your peers and draw on that common bond of TEQ in the Land Cruiser...

    $10.00
    View Details
  • OEM Steel Wheel Chock (SWC-1)

    OEM Steel Wheel Chock

    It should go without saying that ALL vehicles should have a pair of wheel chocks for safety. Every time you are repairing your truck or replacing a tire or anything that requires you to be under it, a wheel chock is a must. If you have a pair of wheel...

    $26.00
    Add to Cart
  • Connector Pin Tool-basic (PST-2)

    Connector Pin Tool-basic

    If you own any Toyota long enough you will eventually need to either modify or repair an electrical connector. This can be daunting because it seems everyone is already having a hard enough time building up the courage to even commit to "cutting the...

    $43.00
    Pre-Order Now
  • Air Coupler and SB175 Bracket KIT (ACB-5KIT)

    Air Coupler and SB175 Bracket KIT

    The Air Coupler and SB175 Bracket KIT is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when...

    $130.00
    View Details
  • Air Coupler and SB175 Bracket (ACB-5) for On Board Air and Mounting the Anderson SB175 connector

    Air Coupler and SB175 Bracket

    This is the bracket that is ideal for anyone looking to mount both air and power on their vehicle. This bracket gives a safe/secure place to mount both the air coupler and the SB175 for hi-amperage power. MADE in USA

    $45.00
    View Details
  • Air Coupler and SB50 Bracket KIT (ACB-4KIT) for On Board Air and mounting the Anderson SB50

    Air Coupler and SB50 Bracket KIT

    The Air Coupler and SB50 Bracket KIT is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it...

    $95.00
    View Details
  • Air Coupler and SB50 Bracket (ACB-4) for On Board Air and Mounting the Anderson SB50 connector

    Air Coupler and SB50 Bracket

    The Air Coupler and SB50 Bracket is designed for mounting both power and air connections in locations where you need them. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it is...

    $40.00
    View Details
  • Air Coupler Bracket- guarded KIT (ACB-3KIT)

    Air Coupler Bracket- guarded KIT

    This Air Coupler Bracket Guarded KIT has everything you need for the last section of your On Board Air install. This KIT includes the coupler, the bulkhead, the air hose fittings, the guarded bracket, the hardware and 10ft of black nylon tubing. Simply...

    $68.00
    View Details
  • Air Coupler Bracket- Guarded (ACB-3) for On Board Air

    Air Coupler Bracket- Guarded

    The Guarded Air Coupler Bracket is designed for mounting in locations that you know it will be bumped or stepped on. There is a second ring that protects the front edge of the air coupler and prevents the coupler from being damaged when it is stepped on...

    $27.00
    View Details
  • Air Coupler Bracket- angled KIT (ACB-2KIT) for On Board Air

    Air Coupler Bracket- angled KIT

    This Air Coupler Bracket Angled KIT has everything you need for the last section of your On Board Air install. This is NOT the cheap Chinese stuff you can easily pick up at Harbor Freight. These are all top-of-the-line fittings. This KIT includes the...

    $64.00
    View Details
  • Air Coupler Bracket- Angled (ACB-2) for On Board Air

    Air Coupler Bracket- Angled

    This Air Coupler Bracket is ideal for mounting off the edge of a drawer system or mounting under a bumper or fender where a 90* angle is needed for preferred mounting positions. This angled Air Coupler Bracket is made from 1/8" thick 316 Stainless Steel...

    $20.00
    View Details
  • Air Coupler Bracket- flat KIT (ACB-1KIT) for On Board Air

    Air Coupler Bracket- flat KIT

    This Air Coupler Bracket Flat KIT has everything you need for the last section of your On Board Air install. This is NOT the cheap Chinese stuff you can easily pick up at Harbor Freight. These are all top-of-the-line fittings. This KIT includes the...

    $60.00
    View Details
  • Air Coupler Bracket- flat (ACB-1)

    Air Coupler Bracket- flat

    This Air Coupler Bracket is ideal for mounting off the edge of a drawer system or mounting under a bumper or fender. This flat Air Coupler Bracket is made from 1/8" thick 316 Stainless Steel and then is powder coated black. Mounting hardware is also...

    $17.00
    View Details
  • OEM Magnetic Transfer or Trans Case Drain Plug Kit (DPK-2)

    OEM Magnetic Transfer or Trans Case Drain Plug Kit

    These OEM Magnetic Transfer Case Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs (does not fit the FJ Cruiser auto). These are the hex plugs that replace the easily damaged drain plugs. The originals can be easily damaged from a tool rounding out...

    $10.50
    Add to Cart
  • Toyota Magnetic Differential Plug Kit (DPK-1)

    OEM Magnetic Differential Plug Kit

    These OEM Magnetic Differential Plugs fit nearly all Toyota 2WD and 4WD trucks and SUVs with M18 threads. These are the hex plugs that replace the easily damaged diff fill and drain plugs. The originals can be easily damaged from off-roading or from a...

    $10.50
    Add to Cart