Created with Sketch. Created with Sketch.

80 Series 4" Lift

  • LANDTANK 80 Series Double-Cardon Front Drive Shaft (DCS-1) LANDTANK 80 Series Double-Cardon Front Drive Shaft (DCS-1)

    80 Series Double-Cardan Front Drive Shaft

    Note: This is NOT a replacement for a stock Tacoma driveshaft. Please allow 1-3 weeks for delivery. NOTE: as of 8/27/18 the price was raised due to increased costs of viable cores, the increase in steel costs and increase of cost of Toyota Japanese...

    $595.00
  • 80 Series E-Brake Drop Block (EDB-1)

    80 Series E-Brake Drop Block

    If you are going to lift your 80 Series Toyota Land Cruiser 3in. or more than you will need to drop your E-Brake line where its mounted to the frame to keep it from binding. This drop block is a simple replacement using a zinc plated steel spacer with...

    $30.00
    Add to Cart
  • 80 Series Front Swaybar Drop Blocks (SDB-1)

    80 Series Front Swaybar Drop Blocks

    When lifting your 80 Series Land Cruiser, one of the steps to get the truck to give you the same stability on the road is to lower the sway bar end links and/or lower the sway bar mounting brackets. For the front this is easily done by simply dropping...

    $60.00
    Add to Cart
  • 80 Series OEM Brake Hose Kit for 2-4in Lifts (BHK-1) 80 Series OEM Brake Hose Kit for 2-4in Lifts (BHK-1)

    80 Series OEM Brake Hose Kit for 2-4in Lifts

    NOTE: As a kit fits- 8/1992-1/1998 FZJ80 trucks When you finally decide to lift your 80 Series Land Cruiser its important that you also extend the length of the brake hoses or else your stock length hoses will wind up becoming limiting straps when your...

    $165.00
    Add to Cart
  • 80 Series Rear Bump Stop Blocks (BSB-1)

    80 Series Rear Bump Stop Blocks

    When doing a lift or increasing the tire size on the 80 Series Land Cruiser you may need to adjust the rear bump stops in order to keep the axle from compressing so much that the tires start rubbing the inner fender well or worse, the fender flares. This...

    $65.00
    Add to Cart
  • 80 Series Swaybar Bushing Kit (SBB-1KIT) 80 Series Swaybar Bushing Kit (SBB-1KIT)

    80 Series Swaybar Bushing Kit

    This the 80 Series Land Cruiser Swaybar bushing kit. These OEM bushings will handle the frame mounted "D" brackets for the swaybar and also the rubber ends of the swaybar. This kit is only for the FZJ-80 trucks. Will not work for 90-91 FJ80s. This kit...

    $50.00
    Add to Cart
  • Land Cruiser Shock Bolt and Washer (SBW-1)

    Land Cruiser Shock Bolt and Washer

    These are the shock bolts that are used in several models of Land Cruiser. These tend to not only rust out but they also tend to get damaged during off-roading. • 60/62 series: rear upper and lower, front lowers (6 needed)• 70 series Heavy...

    $2.85
    Add to Cart
  • Replacement Bolts for LANDTANK Caster Plates (CCP-4) Replacement Bolts for LANDTANK Caster Plates (CCP-4)

    Replacement Bolts for LANDTANK Caster Plates

    NOTE: This is caster hardware ONLY for LANDTANK caster plates. LANDTANK caster correction plates increase the width of the caster bracket by 1/4". Although you get new hardware when you purchase caster correction plates, you DO need to replace the...

    $23.00
    Add to Cart
  • LANDTANK 80 Series DIY Pan Hard Joints (PHJ-1)

    80 Series DIY Pan Hard Joints

    This Do-It-Yourself kit includes the two weld kits needed to modify both front and rear panhard bars. This modification is typically needed when lifting your 80 Series Land Cruiser 3-4". The panhard is cut at both frame sides and then the new...

    $195.00
    Add to Cart
  • LANDTANK 80 Series Swaybar Frame Brackets (SFB-1) LANDTANK 80 Series Swaybar Frame Brackets (SFB-1)

    80 Series Swaybar Frame Brackets

    Sway bar frame brackets. Each kit is designed to upgrade OEM side mounted sway bar brackets typically found on the 93-95 80 series Land Cruiser to bottom mount sway bar brackets. Each kit includes two brackets and mounting hardware kit. •...

    $165.00
    Add to Cart