Created with Sketch. Created with Sketch.

Studs, Lugs & Hardware

  • 11mm Driveshaft Bolt- Spare (DCS-11) 11mm Driveshaft Bolt- Spare (DCS-11)

    11mm Driveshaft Bolt- Spare

    Individual OEM 11mm driveshaft bolt. Although you can get an entire 10mm driveshaft hardware or 11mm driveshaft hardware kit, sometimes it helps to have a few 11mm bolts as a spare.

    $1.50
    Add to Cart
  • 80 Series 1FZ Alternator Adjusting Block (AAB-1) Alternator belt adjusting gone wrong

    80 Series 1FZ Alternator Adjusting Block

    This little sucker is known to be a pain in the neck because either this is stripped or the adjusting bolt itself is stripped or worse, bent. The center bolt for this block, for the alternator, is the lock that is ALWAYS overlooked when people attempt to...

    $7.75
    Add to Cart
  • 80 series 1FZ Alternator Adjusting Bolt (AAB-2) 80 series 1FZ Alternator Adjusting Bolt (AAB-2)

    80 series 1FZ Alternator Adjusting Bolt

    This is the OEM alternator adjusting bolt found on all 80 Series Land Cruisers with the 3FE and 1FZ motors. This bolt is commonly broken or stripped because the locking bolt on the adjuster block wasn't loosened first. Also fits: Land Cruisers with a...

    $2.20
    Add to Cart
  • 80 Series 1FZ cat mounting hardware, 95-97 (CMH-1) 80 Series 1FZ cat mounting hardware, 95-97 (CMH-1) OLD hardware

    80 Series 1FZ cat mounting hardware, 95-97

    Anytime you find yourself needing to fix an exhaust leak or repair some hardware or if you are installing a turbo onto your 95-97 80 Series, this is the ideal kit. This includes all of the rusted out hardware you will need to replace along with both...

    $58.00
    Add to Cart
  • 80 Series Driveshaft Hardware Kit-Rear 11mm (DCS-3) 80 Series Driveshaft Hardware Kit-Rear 11mm (DCS-3)

    80 Series Driveshaft Hardware Kit-Rear 11mm

    This is the complete driveshaft hardware for most Land Cruisers on the road. This kit replaces the washer/nut on the transfer case side and the bolt/washer/nut on the differential side. The 11mm rear driveshaft hardware fits:• All FJ60 Series Land...

    $20.00
    Add to Cart
  • 80 Series OEM Lower Knuckle Stud Kit (KAN-2)

    80 Series OEM Lower Knuckle Stud Kit

    When you are looking to replace your factory knuckle studs due to a rebuild or because your knuckle arm is missing a bolt, these are the OEM replacements. The only difference is the E12 Torx which makes them easier to install. This is for one side and...

    $17.50
    Add to Cart
  • Exhaust Manifold Downpipe Kit (EMK-1)

    Exhaust Manifold Downpipe Kit

    Exhaust Manifold Downpipe Kit for all 1FZ Toyota Land Cruisers. This is the kit that is needed when you need to replace your Y-pipe and front catalytic converter. Generally speaking the original manifold studs are likely rusted and should be replaced...

    $69.00
    Add to Cart
  • Land Cruiser Shock Bolt and Washer (SBW-1)

    Land Cruiser Shock Bolt and Washer

    These are the shock bolts that are used in several models of Land Cruiser. These tend to not only rust out but they also tend to get damaged during off-roading. • 60/62 series: rear upper and lower, front lowers (6 needed)• 70 series Heavy...

    $2.85
    Add to Cart
  • Land Cruiser Starter Mounting Stud- M12 (SMS-12) Land Cruiser Starter Mounting Stud- M12 (SMS-12)

    Land Cruiser Starter Mounting Stud- M12

    This is the starter mounting stud used on all 1FZFE, 2F, 3FE, F motors up to 1993. Part no. 90116-12005 This stud measures:• 43mm length• M12 x 1.25 x 18mm fine thread• M12 x 1.75 x 8mm course thread Made in USA

    $1.50
    Add to Cart